Jeti Hendheld RC 2.4 GHz No. of channels: 8 80001586 User Manual
Product codes
80001586
computer radio control system
EN
menu directly to the first one will be disabled (and vice versa from
the first row to the last).
the first row to the last).
12.
Screenshot Capture Switch
This feature gives you the ability to create your own screenshots.
After you activate the switch, a bitmap is created in the root folder of
the SD card. You can create up to 1000 screenshots.
After you activate the switch, a bitmap is created in the root folder of
the SD card. You can create up to 1000 screenshots.
13.
PPM connector settings
This option presents the possibility to configure the internal
connector labeled as PPM Output (please refer to the chapter 3.7
PPM Output Connector):
- Off – the connector output (pin No. 4) will not generate any kind of
signal.
- PPM Positive – the connector output (pin No. 4) will generate
standard eight-channel PPM signal with positive pulses.
- PPM Negative – the connector output (pin No. 4) will generate
inverted eight-channel PPM signal with negative pulses (0V level).
- EX Data Stream – the connector output (pin No. 4) will generate a
digital data stream containing EX telemetry. The format of
transmitted sensor/receiver data is described in the document JETI
Telemetry Communication Protocol. The communication is
unidirectional and cannot be used to configure the transmitter or
any linked device. If you connect the RCDroidBox device to the
transmitter, you will need to set this option.
connector labeled as PPM Output (please refer to the chapter 3.7
PPM Output Connector):
- Off – the connector output (pin No. 4) will not generate any kind of
signal.
- PPM Positive – the connector output (pin No. 4) will generate
standard eight-channel PPM signal with positive pulses.
- PPM Negative – the connector output (pin No. 4) will generate
inverted eight-channel PPM signal with negative pulses (0V level).
- EX Data Stream – the connector output (pin No. 4) will generate a
digital data stream containing EX telemetry. The format of
transmitted sensor/receiver data is described in the document JETI
Telemetry Communication Protocol. The communication is
unidirectional and cannot be used to configure the transmitter or
any linked device. If you connect the RCDroidBox device to the
transmitter, you will need to set this option.
14.
Check signal before flight
It is possible to check the signal strength immediately after the
model is turned on and connected to the transmitter. If you set Yes
for this option, a warning message is generated for antenna signal
levels less than 8. To make this function work correctly, you should be
model is turned on and connected to the transmitter. If you set Yes
for this option, a warning message is generated for antenna signal
levels less than 8. To make this function work correctly, you should be
4.
4.
located a distance of up to several meters from the model at the
moment of switching it on. If the message is still present, please
perform a range test and check the installation of the on-board
electronic equipment.
moment of switching it on. If the message is still present, please
perform a range test and check the installation of the on-board
electronic equipment.
9.6.2 Servo & Range Test
This menu allows you to perform a range test and servo tests.
During the servo test it is possible to send the test output to all of the
channels which are active in the current model setup. The servo
speed item allows you to adjust the travel time for the servos during
the servo test. During the test, the servos will only be driven to their
programmed maximum throws. You can select which servos will be
included in the test.
During the servo test it is possible to send the test output to all of the
channels which are active in the current model setup. The servo
speed item allows you to adjust the travel time for the servos during
the servo test. During the test, the servos will only be driven to their
programmed maximum throws. You can select which servos will be
included in the test.
1
2
3
4
5
6
129