Texas Instruments Delfino C28343 Experimenter's Kit TMDSDOCK28343 TMDSDOCK28343 Data Sheet
Product codes
TMDSDOCK28343
Quick Start Guide
SPRUGP7 – June 2009
TMS320C28343 Experimenter’s Kit Overview
The C28343 Experimenter’s Kit is a quick, easy, and low-cost way to evaluate the TMS320C2834x family
of devices. It consists of a DIM100 docking station and a C28343 DIM100 controlCARD. The docking
station is a small mother board which accepts a DIM100 style controlCARD. It provides the required 5V
power supply and provides access to many of the GPIO signals. Additionally, it provides two prototyping
areas (one on each side of the DIM100 connector) with an array of 0.1” space that is plated through holes
for wire-wrapping and soldering. Other features of the docking station include:
of devices. It consists of a DIM100 docking station and a C28343 DIM100 controlCARD. The docking
station is a small mother board which accepts a DIM100 style controlCARD. It provides the required 5V
power supply and provides access to many of the GPIO signals. Additionally, it provides two prototyping
areas (one on each side of the DIM100 connector) with an array of 0.1” space that is plated through holes
for wire-wrapping and soldering. Other features of the docking station include:
•
UART communications header connector
•
Boot jumpers for all boot modes covered by C2834x devices
•
5.0 V supply for prototyping area
•
3.3 V supply for prototyping area
•
All key signals accessible via clearly labeled header pins
The Delfino™ C28343 controlCARD™ is based on the standard DIM100 controlCARD form factor and is
compatible with existing C2000 controlCARD-based application development boards. It is based around
the 179-pin 200MHz TMS302C28343ZHH controller and the card provides access to most signals. The
external memory interface (XINTF) and external ADC interface (ADCSOC) signal are not accessible using
the C28343 controlCARD. These signals can be accessed using the C28346 DIM168 controlCARD, which
is not compatible with C2000 application development boards.
compatible with existing C2000 controlCARD-based application development boards. It is based around
the 179-pin 200MHz TMS302C28343ZHH controller and the card provides access to most signals. The
external memory interface (XINTF) and external ADC interface (ADCSOC) signal are not accessible using
the C28343 controlCARD. These signals can be accessed using the C28346 DIM168 controlCARD, which
is not compatible with C2000 application development boards.
In order to maintain compatibility with existing DIM100-based C2000 application development boards, the
C28343 controlCARD has two onboard ADCs. The two TI ADS7865 modules are connected to the
external ADC interface and use the external memory interface to transfer data at high speeds. They are
capable of sampling 12 bits at 2MSPS and provide 6 ADC channels each, for a total of 12 ADC channels.
This allows the C28343 controlCARD to be used with existing kits. However the software will need to be
modified to utilize the external ADCs.
C28343 controlCARD has two onboard ADCs. The two TI ADS7865 modules are connected to the
external ADC interface and use the external memory interface to transfer data at high speeds. They are
capable of sampling 12 bits at 2MSPS and provide 6 ADC channels each, for a total of 12 ADC channels.
This allows the C28343 controlCARD to be used with existing kits. However the software will need to be
modified to utilize the external ADCs.
The controlCARD™ features include:
•
200MHz TMS320C28343ZHH based DIM100 style controlCARD
•
Compatible with existing C2000 controlCARD based application development boards
SPRUGP7 – June 2009
TMS320C28343 Experimenter’s Kit Overview
1