Microchip Technology MCP3422EV Data Sheet
© 2009 Microchip Technology Inc.
DS22088C-page 15
MCP3422/3/4
4.9
Digital Output Codes and
Conversion to Real Values
Conversion to Real Values
4.9.1
DIGITAL OUTPUT CODE FROM
DEVICE
DEVICE
The digital output code is proportional to the input
voltage and PGA settings. The output data format is a
binary two’s complement. With this code scheme, the
MSB can be considered a sign indicator. When the
MSB is a logic ‘0’, the input is positive. When the MSB
is a logic ‘1’, the input is negative. The following is an
example of the output code:
voltage and PGA settings. The output data format is a
binary two’s complement. With this code scheme, the
MSB can be considered a sign indicator. When the
MSB is a logic ‘0’, the input is positive. When the MSB
is a logic ‘1’, the input is negative. The following is an
example of the output code:
a.
for a negative full scale input voltage: 100...000
Example: (CHn+ - CHn-)
•
PGA = -2.048V
b.
for a zero differential input voltage: 000...000
Example: (CHn+ - CHn-) = 0
c.
for a positive full scale input voltage: 011...111
Example: (CHn+ - CHn-)
•
PGA = 2.048V
The MSB (sign bit) is always transmitted first through
the I
the I
2
C serial data line. The resolution for each
conversion is 18, 16, 14, or 12 bits depending on the
conversion rate selection bit settings by the user.
conversion rate selection bit settings by the user.
The output codes will not roll-over even if the input
voltage exceeds the maximum input range. In this
case, the code will be locked at 0111...11 for all
voltages greater than (V
voltage exceeds the maximum input range. In this
case, the code will be locked at 0111...11 for all
voltages greater than (V
REF
- 1 LSB)/PGA and
1000...00
for voltages less than -V
REF
/PGA.
shows an example of output codes of various
input levels for 18 bit conversion mode.
shows an example of minimum and maximum output
codes for each conversion rate option.
codes for each conversion rate option.
The number of output code is given by:
EQUATION 4-2:
The LSB of the data conversion is given by:
EQUATION 4-3:
shows the LSB size of each conversion rate
setting. The measured unknown input voltage is
obtained by multiplying the output codes with LSB. See
the following section for the input voltage calculation
using the output codes.
obtained by multiplying the output codes with LSB. See
the following section for the input voltage calculation
using the output codes.
TABLE 4-1:
RESOLUTION SETTINGS VS.
LSB
LSB
TABLE 4-2:
TABLE 4-3:
MINIMUM AND MAXIMUM
OUTPUT CODES (NOTE)
OUTPUT CODES (NOTE)
Number of Output Code =
Maximum Code
1
+
(
) PGA
CHn+
CHn-
–
(
)
2.048V
-----------------------------------------
×
×
=
Where:
LSB
2
V
REF
×
2
N
----------------------
2
2.048V
×
2
N
--------------------------
=
=
Where:
N
=
Resolution, which is programmed in
the Configuration Register.
the Configuration Register.
Resolution Setting
LSB
12 bits
1 mV
14 bits
250 µV
16 bits
62.5 µV
18 bits
15.625 µV
Input Voltage:
[CHn+ - CHn-] • PGA
Digital Output Code
≥
V
REF
011111111111111111
V
REF
- 1 LSB
011111111111111111
2 LSB
000000000000000010
1 LSB
000000000000000001
0
000000000000000000
-1 LSB
111111111111111111
-2 LSB
111111111111111110
- V
REF
100000000000000000
< -V
REF
100000000000000000
Note 1:
MSB is a sign indicator:
0: Positive input (CHn+ > CHn-)
1: Negative input (CHn+ < CHn-)
0: Positive input (CHn+ > CHn-)
1: Negative input (CHn+ < CHn-)
2:
Output data format is binary two’s
complement.
complement.
Resolution
Setting
Data Rate
Minimum
Code
Maximum
Code
12
240 SPS
-2048
2047
14
60 SPS
-8192
8191
16
15 SPS
-32768
32767
18
3.75 SPS
-131072
131071
Note:
Maximum n-bit code = 2
N-1
- 1
Minimum n-bit code = -1 x 2
N-1