Microchip Technology AC164338 Data Sheet
Development Systems Ordering Guide
DS30177T-page 32
© 2005 Microchip Technology Inc.
MPLAB
®
ICD 2 In-Circuit Debugger
The MPLAB
ICD 2 module
is a low-cost
development
tool that
connects
between the
PC and the
designer’s
target board,
allowing direct
in-circuit
ICD 2 module
is a low-cost
development
tool that
connects
between the
PC and the
designer’s
target board,
allowing direct
in-circuit
debugging of a target PICmicro
®
MCU or dsPIC
®
DSC.
Programs can be executed in real time or single step,
watch variables established, break points set, memory
read/writes accomplished and more. It can also be
used as a development programmer for the
microcontrollers.
watch variables established, break points set, memory
read/writes accomplished and more. It can also be
used as a development programmer for the
microcontrollers.
The MPLAB ICD 2 allows debugging of selected
Flash-based Microchip microcontrollers using MPLAB
Integrated Development Environment (IDE). This
powerful graphical user interface is included with each
unit as a free tool. It is the ideal tool for embedded
control designers who do not have the budget for a
high-cost, in-circuit emulator.
Flash-based Microchip microcontrollers using MPLAB
Integrated Development Environment (IDE). This
powerful graphical user interface is included with each
unit as a free tool. It is the ideal tool for embedded
control designers who do not have the budget for a
high-cost, in-circuit emulator.
Shared overhead includes: one stack level, some
general purpose file registers, a small bank of program
memory when in the Debug mode and two hardware
pins (RB6 and RB7).
general purpose file registers, a small bank of program
memory when in the Debug mode and two hardware
pins (RB6 and RB7).
The MPLAB ICD 2 is firmware-based, which allows it to
be enhanced to support future microcontroller products
and new features, extending the tool life and making it
a valued buy. Firmware downloads are available from
the Microchip web site at: www.microchip.com.
be enhanced to support future microcontroller products
and new features, extending the tool life and making it
a valued buy. Firmware downloads are available from
the Microchip web site at: www.microchip.com.
Features
• USB (full speed, 2 Mbits/s) and RS-232 interface to
host PC
• Real-time background debugging
• Built-in overvoltage/short-circuit monitor
• Supports low-voltage operation to 2.0 volts
• Diagnostic LEDs (power, busy, error)
• Reading/writing memory space and stack of target
microcontroller
• Erase of program memory space with verification
• Freeze on Halt
• Programs many Flash devices
Ordering Information:
DV164005
MPLAB
®
ICD 2 Module (Includes MPLAB ICD 2 Module, RJ-11 Cable and USB Cable)
DV164006
MPLAB
®
ICD 2 Evaluation Kit
(Includes MPLAB ICD 2 Module, RJ-11 Cable, USB Cable, RS-232 Cable, Power Supply and
PICDEM™ 2 Plus Demonstration Board – DM163022)
PICDEM™ 2 Plus Demonstration Board – DM163022)
DV164007
MPLAB
®
ICD 2 Module ws
(Includes MPLAB ICD 2 Module, RJ-11 Cable, USB Cable, RS-232 Cable and Power Supply)
DV164030
MPLAB
®
ICD 2 with dsPICDEM™ Starter Demonstration Board
DV164032
MPLAB
®
ICD 2 with dsPICDEM 1.1 General Purpose Demonstration Board
DS51264
“MPLAB
®
ICD 2 In-Circuit Debugger/Programmer Product Overview”
(Available at: www.microchip.com)