Microchip Technology XLP 8-BIT Development Board DM240313 DM240313 Leaflet

To obtain the most recent and complete documentation for this demonstration board, including:

- User's Guide

- Board Description

- Board Schematics

- Source Code

- Application Examples

- Links to Web Seminars

please refer to the Microchip web site: www.microchip.com/xlp

EUROPE
Austria - Wels - 43-7242-2244-39
Denmark - Copenhagen - 45-4450-2828
France - Paris - 33-1-69-53-63-20
Germany - Munich - 49-89-627-144-0
Italy - Milan - 39-0331-742611
Netherlands - Drunen - 31-416-690399
Spain - Madrid - 34-91-708-08-90
UK - Wokingham - 44-118-921-5869

                                                  02/18/11

AMERICAS
Atlanta - 678-957-9614
Boston - 774-760-0087
Chicago - 630-285-0071
Cleveland - 216-447-0464
Dallas - 972-818-7423
Detroit - 248-538-2250
Indianapolis - 317-773-8323
Los Angeles - 949-462-9523
Phoenix - 480-792-7200
Santa Clara - 408-961-6444
Toronto - 905-673-0699

Overview
The XLP 8-Bit Development Board is pre-programmed with a demonstration program. The board 
must be connected as described in this document to use the demonstration program. To measure 
current consumption, the current analyzer cable must be set up as described in this document.

XLP 8-Bit Development Board Setup
The kit includes the XLP 8-Bit Development Board, current analyzer cable, USB connection cable, 
bag of 15 jumpers, and Microchip's PIC16LF1947 and PIC18F87K22 microcontrollers. To use the 
kit, follow the steps below:
1.

Insert either the PIC16LF1947 or PIC18F87K22 microcontrollers onto the XLP 8-bit board. 

Make sure you insert the microcontroller as shown in the figure below.

2.

Confirm jumper configurations using the table provided.

3.

Connect the current analyzer cable to the pins as indicated in this document.

Board Power-Up
Supply power to the board in one of the following ways: 
•

Connect the USB cable using the J13 connector. [J8 is ON]

•

Connect two (2) AAA Batteries to B1 & B2, or a coin battery to B3. [J9 is ON; J12 is USED]

•

Connect an external 3.3-S VDC supply to (+VEXT) and (GND). [J10 is ON]

•

Connect Microchip's Harvester device to J17. [J11 is ON]

LED D5 will immediately turn on after power-on. 

Note: Using the table on the next page, confirm your power source jumper configurations 

before supplying power to the board.

The Microchip name and logo and the Microchip logo are registered trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries. PICkit and PICtail is a trademark of Microchip Technology Incorporated in the U.S.A. and other
countries. All other trademarks mentioned herein are property of their respective companies. 
© 2011, Microchip Technology Incorporated, Printed in the U.S.A. All Rights Reserved. 4/11

     

DS51973A

ASIA/PACIFIC
Australia - Sydney - 61-2-9868-6733
China - Beijing - 86-10-8528-2100
China - Chengdu - 86-28-8665-5511
China - Chongqing - 86-23-8980-9588
China - Hong Kong SAR - 852-2401-1200
China - Nanjing- 86-25-8473-2460
China - Qingdao - 86-532-8502-7355
China - Shanghai - 86-21-5407-5533
China - Shenyang - 86-24-2334-2829
China - Shenzhen - 86-755-8203-2660
China - Wuhan - 86-27-5980-5300
China - Xiamen - 86-592-2388138
China - Xian - 86-29-8833-7252
China - Zhuhai - 86-756-3210040
India - Bangalore - 91-80-3090-4444
India - New Delhi - 91-11-4160-8631
India - Pune - 91-20-2566-1512
Japan - Yokohama - 81-45-471-6166
Korea - Daegu - 82-53-744-4301
Korea - Seoul - 82-2-554-7200
Malaysia - Kuala Lumpur - 60-3-6201-9857
Malaysia - Penang - 60-4-227-8870
Philippines - Manila - 63-2-634-9065
Singapore - 65-6334-8870
Taiwan - Hsin Chu - 886-3-6578-300
Taiwan - Kaohsiung - 886-7-213-7830
Taiwan - Taipei - 886-2-2500-6610
Thailand - Bangkok - 66-2-694-1351