Rigol DM3058E Digital-Multimeter, DMM, DM3058E Data Sheet
Product codes
DM3058E
2
Specifications
DC Characteristics
Accuracy ± (% of reading + % of range)
[1]
Function
Range
[2]
Test current or
Load voltage
1 Year
23℃± 5℃
Temperature
Coefficient
0℃ - 18℃
28℃ - 50℃
28℃ - 50℃
DC Voltage
200.000 mV
0.015 + 0.004
0.0015 + 0.0005
2.00000 V
0.015 + 0.003
0.0010 + 0.0005
20.0000 V
0.015 + 0.004
0.0020 + 0.0005
200.000 V
0.015 + 0.003
0.0015 + 0.0005
1000.00 V
[4]
0.015 + 0.003
0.0015 + 0.0005
DC Current
200.000 μA
<8 mV
0.055 + 0.005
0.003 + 0.001
2.00000 mA
<80 mV
0.055 + 0.005
0.002 + 0.001
20.0000 mA
<0.05 V
0.095 + 0.020
0.008 + 0.001
200.000 mA
<0.5 V
0.070 + 0.008
0.005 + 0.001
2.00000 A
<0.1 V
0.170 + 0.020
0.013 + 0.001
10.0000 A
[5]
<0.3 V
0.250 + 0.010
0.008 + 0.001
Resistance
[3]
200.000 Ω
1 mA
0.030 + 0.005
0.0030 + 0.0006
2.00000 kΩ
1 mA
0.020 + 0.003
0.0030 + 0.0005
20.0000 kΩ
100 μA
0.020 + 0.003
0.0030 + 0.0005
200.000 kΩ
10 μA
0.020 + 0.003
0.0030 + 0.0005
2.00000 MΩ
1 μA
0.040 + 0.004
0.0040 + 0.0005
10.0000 MΩ
200 nA
0.250 + 0.003
0.0100 + 0.0005
100.000 MΩ
200 nA || 10 MΩ
1.75 + 0.004
0.2000 + 0.0005
Diode Test
2.0000 V
[6]
1 mA
0.05 + 0.01
0.0050 + 0.0005
Continuity
Test
2000 Ω
1 mA
0.05 + 0.01
0.0050 + 0.0005
Remarks:
[1] Specifications are for 0.5 hour warm-up, “Slow” measurement rate and calibration temperature 18℃ ~ 28℃.
[2] 20% over range on all ranges except for DCV 1000 V, ACV 750 V, DCI 10 A and ACI 10 A.
[1] Specifications are for 0.5 hour warm-up, “Slow” measurement rate and calibration temperature 18℃ ~ 28℃.
[2] 20% over range on all ranges except for DCV 1000 V, ACV 750 V, DCI 10 A and ACI 10 A.
[3] Specifications are for 4-wire measure or 2-wire measure under “REF” operation. ± 0.2 Ω of extra errors will be
generated if perform 2-wire measure without “REF” operation.
[4] Plus 0.02 mV of error per 1 V after the first ±500 VDC.
[5] 30 seconds OFF after 30 seconds ON is recommend for the continuous current that higher than DC 7 A or AC RMS
7 A.
[6] Accuracy specifications are only for voltage measuring at input terminal. The typical value of current under
measure is 1 mA. Voltage drop at the diode junction may vary with current supply.
DC Voltage
Input Resistance
Input Resistance
200 mV and 2 V 10 MΩ or >10 GΩ selectable
(Input signals that exceed ± 2.5 V in these ranges will pass the 100 kΩ (typical) clamp
resistance.)
20 V, 200 V and 1000 V 10 MΩ ± 2%
Input Bias Current
<90 pA, 25℃
Input Protection
1000 V on all ranges
CMRR (common mode
rejection ratio)
120 dB (For the 1 kΩ unbalanced resistance in LO lead, maximum ± 500 VDC)
NMRR (normal mode
rejection ratio)
60 dB at “slow” measurement rate
20 dB are added if open the “AC filter” (Settling time will add 0.35 s while source
impedance nears zero)
Resistance
Testing Method
Testing Method
4-wire resistance or 2-wire resistance optional
For current source refer to LO input
Open-circuit Voltage
P/F in <8 V
Maximum Lead
Resistance
(4-wire resistance)
10% of ranges, on the range of 200 Ω, 1 kΩ, for each lead
1 kΩ, on all other ranges, for each lead
Input Protection
1000 V, on all ranges