Atmel ATmega328P Xplained Mini MEGA328P-XMINI MEGA328P-XMINI Data Sheet
Product codes
MEGA328P-XMINI
232
ATmega48A/PA/88A/PA/168A/PA/328/P [DATASHEET]
Atmel-8271H-AVR- ATmega-Datasheet_08/2014
• Bit 6 – TWEA: TWI Enable Acknowledge Bit
The TWEA bit controls the generation of the acknowledge pulse. If the TWEA bit is written to one, the ACK
pulse is generated on the TWI bus if the following conditions are met:
pulse is generated on the TWI bus if the following conditions are met:
1. The device’s own slave address has been received.
2.
A general call has been received, while the TWGCE bit in the TWAR is set.
3.
A data byte has been received in Master Receiver or Slave Receiver mode.
By writing the TWEA bit to zero, the device can be virtually disconnected from the 2-wire Serial Bus temporarily.
Address recognition can then be resumed by writing the TWEA bit to one again.
Address recognition can then be resumed by writing the TWEA bit to one again.
• Bit 5 – TWSTA: TWI START Condition Bit
The application writes the TWSTA bit to one when it desires to become a Master on the 2-wire Serial Bus. The
TWI hardware checks if the bus is available, and generates a START condition on the bus if it is free. However,
if the bus is not free, the TWI waits until a STOP condition is detected, and then generates a new START
condition to claim the bus Master status. TWSTA must be cleared by software when the START condition has
been transmitted.
TWI hardware checks if the bus is available, and generates a START condition on the bus if it is free. However,
if the bus is not free, the TWI waits until a STOP condition is detected, and then generates a new START
condition to claim the bus Master status. TWSTA must be cleared by software when the START condition has
been transmitted.
• Bit 4 – TWSTO: TWI STOP Condition Bit
Writing the TWSTO bit to one in Master mode will generate a STOP condition on the 2-wire Serial Bus. When
the STOP condition is executed on the bus, the TWSTO bit is cleared automatically. In Slave mode, setting the
TWSTO bit can be used to recover from an error condition. This will not generate a STOP condition, but the TWI
returns to a well-defined unaddressed Slave mode and releases the SCL and SDA lines to a high impedance
state.
the STOP condition is executed on the bus, the TWSTO bit is cleared automatically. In Slave mode, setting the
TWSTO bit can be used to recover from an error condition. This will not generate a STOP condition, but the TWI
returns to a well-defined unaddressed Slave mode and releases the SCL and SDA lines to a high impedance
state.
• Bit 3 – TWWC: TWI Write Collision Flag
The TWWC bit is set when attempting to write to the TWI Data Register – TWDR when TWINT is low. This flag
is cleared by writing the TWDR Register when TWINT is high.
is cleared by writing the TWDR Register when TWINT is high.
• Bit 2 – TWEN: TWI Enable Bit
The TWEN bit enables TWI operation and activates the TWI interface. When TWEN is written to one, the TWI
takes control over the I/O pins connected to the SCL and SDA pins, enabling the slew-rate limiters and spike
filters. If this bit is written to zero, the TWI is switched off and all TWI transmissions are terminated, regardless of
any ongoing operation.
takes control over the I/O pins connected to the SCL and SDA pins, enabling the slew-rate limiters and spike
filters. If this bit is written to zero, the TWI is switched off and all TWI transmissions are terminated, regardless of
any ongoing operation.
• Bit 1 – Reserved
This bit is a reserved bit and will always read as zero.
• Bit 0 – TWIE: TWI Interrupt Enable
When this bit is written to one, and the I-bit in SREG is set, the TWI interrupt request will be activated for as long
as the TWINT Flag is high.
as the TWINT Flag is high.
22.9.3 TWSR – TWI Status Register
• Bits 7:3 – TWS: TWI Status
These 5 bits reflect the status of the TWI logic and the 2-wire Serial Bus. The different status codes are
described later in this section. Note that the value read from TWSR contains both the 5-bit status value and the
described later in this section. Note that the value read from TWSR contains both the 5-bit status value and the
Bit
7
6
5
4
3
2
1
0
TWS7
TWS6
TWS5
TWS4
TWS3
–
TWPS1
TWPS0
TWSR
Read/Write
R
R
R
R
R
R
R/W
R/W
Initial Value
1
1
1
1
1
0
0
0