ParkZone Radian RTF PKZ4700 Data Sheet

The Spektrum trademark is used with permission of Bachmann Industries, Inc.

 

1. Install Receiver

                      Example of AR500 installed in E-flite

®

 Apprentice

 

Though in general it is non-critical, optimum installation of the antenna is to 

orient the tip of the long antenna perpendicular to the short antenna. The tip 

on the long antenna should be a least 2 inches from the short antenna. 

                 Example of AR500 installed in Hangar 9

®

 Pulse

™

 XT 60

   Note: Observe polarity when installing batteries. 

  

  A.   Plug the bind plug into the receiver’s BATT/BIND port. In systems utiliz-

ing a separate battery pack and 3-wire switch, plug the bind plug into the 

charge jack. 

  B.  Power up the receiver. The LED on the receiver will be flashing. 

  C.   Move the sticks and switches on the transmitter to the desired failsafe 

positions (low throttle and neutral control positions). 

  D.   Pull and hold the Trainer Switch on the transmitter while turning the 

transmitter on. Release the trainer switch once the LEDs on the front of 

the transmitter flash.

  E.   The LED on the receiver will go solid amber and the system will connect 

after several seconds. 

  F.  Remove the bind plug from the charge jack or bind port. 

      

      Typical Electric - Rx uses the ESC for power.

Typical Glow/Gas - uses receiver pack and 3-wire switch.

 

 

 

 

 

 

 

 

 

 

 

 

   Lack of power to the receiver and servos is a leading cause of failure. If you 

are using a receiver pack, ensure that it is properly charged and check the 

voltage under load (HAN172). Do not fly if voltage is below 4.8V for a  

4-cell pack. 

  

In systems using a BEC, ensure that you are not driving more than the man-

ufacturer’s recommended number of servos for your BEC/Speed control.  

 

If at anytime, the voltage should fall below the receiver’s operating threshold, 

an interruption in the link may occur followed by a blinking light on the 

receiver. A more accurate way to test a questionable setup is to measure the 

voltage per the instructions on page 17.

 

   Note: If the receiver power is cycled without cycling the transmitter, a blink-

ing light will also occur. In this case, this does not indicate a problem.  

Cycle the Tx power, and then the Rx, to reset the light.

5.  Control Surface Check  

Turn on the transmitter followed by the receiver and check that the direction of each 

channel is correct. Use the servo reversing switches on the front of the transmitter 

to change the direction if necessary. 

 

6. Re-Bind the System 

   After you’ve set up your model, it’s important to re-bind the system so the true low 

throttle position is stored. If the signal is lost, the throttle servo will drive to a low 

throttle safe position.

      

  

 

1.  With the model resting on the ground, stand 30 paces  

(approximately 90 feet/28 meters) away from the model.

2.  Face the model with the transmitter in your normal flying position  

and pull and hold the Trainer Switch while toggling the HI/LO Rate Switch

  four times. The LEDs will flash and the alarm will sound indicating the

  system is in range check mode.

3.  You should have total control of the model with the Trainer Switch pulled 

at 30 paces (90 feet/28 meters). 

4. If control issues exist, call the Horizon Support Team at 1-877-504-0233

  or go to horizonhobby.com to find a local Spektrum distributor in your 

  country of service.

Revised 12/08  13639.1

Pull and hold the Trainer Switch

30 paces (90 feet/28 meters)

Leaders in Spread Spectrum Technology

Tape antenna in place. 

Do not allow tip to 

touch metal.

A. Insert Bind Plug

Receiver pack and 3-wire switch

B. Apply power to system

A, B. Insert bind plug into charge  

   

  jack, apply power

C, D. Pull trainer switch, turn power on

Note: Continuing to hold the 

trainer switch during the binding 

process will prevent preset failsafe 

positions from being learned by  

the receiver.