ParkZone Sukhoi SU-29MM PKZ8050 Data Sheet

The included AR636 receiver has been programmed for operation in only this 
aircraft, providing the following selectable fl ight modes. The programming in 
this receiver cannot be changed by the user.

 Mode: Switch position 0 

This mode delivers agile response, with the important addition of automatic 
recovery from any attitude. Release BOTH sticks and the aircraft returns to 
upright, fl ight. Releasing only one stick will not provide automatic recovery. Use 
this mode for slow fl ying and 3D maneuvers such as Harrier Rolls. Flying at 
high speed in this mode will cause oscillation. 

AS3X 3D Mode: Switch position 1 
This mode uses high rates and high gains to deliver extreme maneuverability 
with maximum stability at low airspeeds. Use this mode for slow fl ying and 3D 
maneuvers such as Hovers and Harriers. Flying at high speed in this mode will 
cause oscillation.

AS3X Precision Mode: Switch position 2 
This mode uses low rates and low gains to deliver precise response at high 
airspeeds. Use this mode to trim the aircraft and fl y fast precision maneuvers.

Throttle, Aileron, Elevator and Rudder are in Normal position. 

DX6i

*(Flap System) Norm …100  Land †100

DX6

*(Channel Input Confi g) Gear is B, Aux1 is switch i

DX7

*(Flap System) Norm † 100  Mid †100  Land … 100 
(3 pos Aux1 switch–0 & 1 are normal 2 is panic

DX7s

*(Switch Select) Gear to INH, FM to INH, Flap to Gear, Trainer to Aux1

DX8

*(Switch Select) Gear to INH, FM to Gear, Flap to INH, Trainer to Aux 1

DX9

*(Channel Input Confi g) Gear is B, Aux1 is switch i

DX10t

*(Channel Input Confi g) Gear is A, Aux1 is R stick

DX18

*(Channel Input Confi g) Gear is B, Aux1 is switch i

N = Normal           R = Reverse

If using any DSM2/DSMX transmitter, the radio will have to be confi gured 
correctly for the SAFE system to work properly.

•  SAFE Flight mode is selected using Channel 5 signal (high, middle, low)
•  Panic mode is selected with Channel 6 signal (high, low)

*Refer to your transmitter’s manual for more information about transmitter 
setup.

IMPORTANT: A transmitter with a 2-position channel 5 switch will only allow 
the use of position 0 or position 2 fl ight modes.

DX6i

1. Go to the SETUP LIST MENU
2. Set MODELTYPE: ACRO         
3. Set REVERSE: Gear Channel   
4. Go to ADJUST LIST MENU
5. Set TRAVEL ADJ: Gear/Fmode (0)…100%; Gear/Fmode  (1)† 40%
6. Set FLAPS: Norm …100; LAND †100
7. Set MIX 1: ACT; Gear „Gear ACT,  RATE D 0%; U + 100%,  SW MIX, TRIM INH
Resulting in: 

The Gear and Mix switches operate the 3 SAFE modes
Gear 0; Mix 0 = Stagility™ Mode
Gear 1; Mix 0 = AS3X 3D Mode
Gear 1; Mix 1 = AS3X Precision Mode
The Flap switch operates Panic Recovery:
Position 0=Off, Position 1=On. (not a momentary switch)

•  If you feel you have lost control in 

any mode, hold the Panic Recovery 
button and reduce throttle. The SAFE 
technology will return the aircraft 
to upright fl ight.

•  Always fl y at a safe altitude, as 

Panic Recovery may cause the 
aircraft to lose some altitude when 
leveling the wings.

 

•  Release the Panic Recovery button 

to turn off Panic mode and return to 
the current SAFE fl ight mode with 
full stick control again.

IMPORTANT: If the aircraft is upside 
down when the Panic Recovery button 
is pressed, suffi cient altitude is re-
quired for the aircraft to return to 
upright fl ight.