Numark DJ Controller NV 102764 Data Sheet

 

 
Pitch Controls 

36.

  Tap: Tap this button at the same tempo as the track to help the software detect a more 

accurate BPM reading.  

37.

  Range / Keylock: Press this to adjust the range of the Pitch Fader to ±8%, ±16%, and 

±50%. 

Press and hold Shift and then press this button to activate or deactivate Keylock: the key 
of the song will lock to whatever position the pitch fader is at when Keylock is activated. 
This feature allows you to change the speed of the song without changing the key. 

38.

  Takeover LEDs: When you select the other Deck with the Deck Select switch, the 

position of the NV's Pitch Fader may not match the Pitch setting for that Deck in the 
software. Slowly move the Pitch Fader in the direction indicated by the Takeover LED 
arrow until it turns off. At this point, the Pitch Fader matches the Pitch setting in the 
software and can control it again. 

39.

  Pitch Fader: Controls the track's playback speed. An LED next to the fader will light up 

when set at 0%. 

40.

  Pitch Bend ( + / – ): Press or hold down either of these buttons to temporarily adjust the 

track's playback speed. When released, the track playback will return to the speed 
designated by the Pitch Fader. 

41.

  Beatkeeper: This meter is an aid for matching the tempo of both decks. When the white 

center LED is lit, the BPMs are matched. Otherwise, the meter will tend towards the 
faster deck. The further from center, the greater the difference between the two BPMs.  

 

42.

  Display: Use this screen to view menus, options, parameters, and settings.  

43.

  Sel Knob: Use this knob to scroll through lists of tracks, Crates, etc. in the software. You 

can also press it to move between the panels shown in the software.  

44.

  Fwd / Back: This button moves the selector between various panels in the software. 

45.

  Load / Prep.: Press this button while a track is selected to assign it to the Deck.  

Press and hold Shift and press this button to add a selected track to the list of tracks in 
the Prepare Area in the software. 

46.

  Panel / Area: Press this to toggle through the Recording, Effects, and Sampler panels. 

Press and hold Shift and then press this button to toggle through the Files, Browse, 
Prepare, and History panels. 

47.

  D. View / S. View: Press this button to toggle through the available NV display modes. 

Press and hold Shift and then press this button to toggle through the available software 
display modes. 

 

48.

  FX 1, FX 2, FX 3: These buttons have different functions on each Deck depending on the 

current FX Mode: Single-FX Mode or Multi-FX Mode. Please see the User Guide for 
more information. 

49.

  FX 1 Knob, FX 2 Knob, FX 3 Knob: These knobs have different functions on each Deck 

depending on the current FX Mode: Single-FX Mode or Multi-FX Mode. Please see the 
User Guide for more information. 

50.

  Beat / Mode: Tap this button repeatedly at the desired tempo to set the rate of the 

effects' low-frequency oscillators (LFOs). Press and hold this button to reset Beat 
Multiplier to the Deck's BPM. Press and hold Shift and then press this button to switch 
between Single-FX Mode and Multi-FX Mode. 

51.

  Beat Knob: Turn this knob to set the Time Division for the selected effects. 

52.

  FX Assign: Use these buttons to apply Effect A and/or B to the corresponding channel. 

You can apply Effect A and/or B to the entire Program Mix by using the FX Send buttons 
below the Master Volume knob. (Each effect can be applied to any or all of the four 
channels and/or the Program Mix.)