Renkforce 3D printer RF1000 Single extruder (value.974113) RF1000 Data Sheet

Attachment of the threaded pin to the motor pinion 

M3 

0.7 Nm

Attachment of the ball bearing for belt tensioner to the basic body 

M4 

3 Nm

Attachment of the spacer to the bottom plate 

M5 

5.4 Nm

Attachment of the actuator to the bottom plate 

M3 

1.9 Nm

Attachment of the ball bearing to the belt tensioner basic body 

M4 

3 Nm

Attachment of the guide rail to the X-plate 

M4 

4 Nm

Attachment of the limit switch to the limit switch holder 

M2 

0.3 Nm

Attachment of the limit switchholder to the X-plate 

M3 

1 Nm

Attachment of the belt holder to the guide carriage plate 

M3 

1.1 Nm

Attachment of the feed holder block to the guide carriage plate 

M4 

4 Nm

Attachment of the guide carriage plate to the guide carriage 

M4 

4 Nm

Attachment of the motor holder and fan sheet to the feed holder block 

M4 

4 Nm

Attachment of the extruder holder to the elongation measuring strip 

M5 

5.4 Nm

Attachment of the holding plate for the end stop with elongation measuring strips 

M4 

3 Nm

to the guide carriage plate
Attachment of the end stop to the holder plate for end stop actuation 

M4 

3 Nm

Attachment of the threaded pin to the small pinion on the actuator motor 

M3 

0.7 Nm

Attachment of the motor to the motor holder 

M3 

1.5  Nm

Attachment of the extruder to the extruder holder 

M8 

1.4 Nm

Attachment of the feed basic part to the motor holder 

M4 

3 Nm

Attachment of the actuator to the X-plate 

M3 

1.9 Nm

Attachment of the drag chain end piece to the holder for the end stop 

M3 

1.2 Nm

Attachment of the fan to the fan sheet 

M2.5 

0.7 Nm

Attachment of the ball bearing to the belt tensioner basic body  

M4 

3 Nm

Attachment of the guide rail to the Y-plate 

M4 

4 Nm

Attachment of the actuator to the Y-plate 

M3 

1.9 Nm

Attachment of the drag chain end piece to the holding block for the guide rail 

M3 

1.2 Nm

Attachment of the holding block for the guide rail to the Y-plate 

M3 

1.9 Nm

Attachment of the drag chain end piece to the Y-plate 

M3 

1.2 Nm

Attachment of the holder for the limit switch to the limit switch 

M2 

0.3 Nm

Attachment of the undertable holder to the limit switch holder 

M3 

1.1 Nm

Attachment of the undertable holder to the belt tappet angle 

M3 

1.1 Nm

Attachment of the drag chain end piece to the undertable 

M3 

1.2 Nm

Attachment of the undertable to the Y-plate with the guide carriage 

M4 

4 Nm

Attachment of the threaded circulation spindles to the Y-plate 

M5 

5.4 Nm

Attachment of the actuation for the end stop to the Y-plate 

M4 

3.4 Nm

Attachment of the hexagon threaded bolts for the limit switch actuation to the Y-plate 

M3 

1.1 Nm

Attachment of the installed bottom plate to the installed X-plate 

M5 

5.4 Nm

Attachment of the pinion to the ball circulation spindle 

M3 

0.7 Nm

Attachment of the left and right side parts 

M4 

4 Nm