Siemens SINAMICS G110 0.12 kW 1-phase frequency inverter, 230 Vac to , 6SL3211-0AB11-2BA1 6SL3211-0AB11-2BA1 Data Sheet
Product codes
6SL3211-0AB11-2BA1
04/2003 Commissioning
SINAMICS G110 Operating Instructions
6SL3298-0AA11-0BP0
49
3.4.5 Reset to Factory default
To reset all parameters to the factory default settings; the following parameters
should be set as follows:
1. Set P0010=30.
2. Set P0970=1.
NOTE
The reset process can take up to 3 minutes to complete.
should be set as follows:
1. Set P0010=30.
2. Set P0970=1.
NOTE
The reset process can take up to 3 minutes to complete.
3.4.6 External Motor Thermal Overload Protection
When operated below rated speed, the cooling
effect of fans fitted to the motor shaft is reduced.
Consequentially, most motors require de-rating
for continuous operation at low frequencies. To
ensure that the motors are protected against
overheating under these conditions, a PTC
temperature sensor must be fitted to the motor
and connected to the inverter control terminals
as shown in Figure 3-7.
To enable the trip function set up one of the
digital inputs using P0701 (DIN0) or P0702
(DIN1) or P0703 (DIN2) to a value of 29.
effect of fans fitted to the motor shaft is reduced.
Consequentially, most motors require de-rating
for continuous operation at low frequencies. To
ensure that the motors are protected against
overheating under these conditions, a PTC
temperature sensor must be fitted to the motor
and connected to the inverter control terminals
as shown in Figure 3-7.
To enable the trip function set up one of the
digital inputs using P0701 (DIN0) or P0702
(DIN1) or P0703 (DIN2) to a value of 29.
NOTE
Due to the electrical noise emitted by the PTC cables it is recommended that the
PTC cables are routed parallel to the motor cables and not the inverter control
cables.
Due to the electrical noise emitted by the PTC cables it is recommended that the
PTC cables are routed parallel to the motor cables and not the inverter control
cables.
3.4.7 Cloning Parameters with the BOP
A single parameter set can be uploaded from an inverter and then downloaded into
another inverter. To clone a parameter set from one inverter to another, the
following procedure should be performed:
another inverter. To clone a parameter set from one inverter to another, the
following procedure should be performed:
1. Connect the Basic Operator Panel (BOP) to the inverter.
2. Ensure that it is safe to stop the inverter.
3. Stop the inverter.
4. Set parameter P0003 to 3.
5. Set parameter P0010 to 30 to enter Cloning Mode.
6. Set parameter P0802 to 1 to start the upload from the Inverter to the BOP.
7. During the upload “BUSY” will be displayed.
8. The BOP and the inverter will not react to any commands during upload.
9. If the upload has been completed successfully, the BOP display will return
2. Ensure that it is safe to stop the inverter.
3. Stop the inverter.
4. Set parameter P0003 to 3.
5. Set parameter P0010 to 30 to enter Cloning Mode.
6. Set parameter P0802 to 1 to start the upload from the Inverter to the BOP.
7. During the upload “BUSY” will be displayed.
8. The BOP and the inverter will not react to any commands during upload.
9. If the upload has been completed successfully, the BOP display will return
to normal and the inverter will return to a ready state.
10. If the upload has failed:
a. Attempt another upload.
or
b. Perform a factory reset.
11. The BOP can now be removed from the inverter.
Figure 3-7
Motor Overload PTC