Panasonic Microswitch 30 Vdc 0.5 A 1 x On/(On) AV402461J IP40 momentary 1 pc(s) AV402461J Data Sheet
Product codes
AV402461J
AV4
124
NOTES
Hinge lever type
mm General tolerance:
±0.15
1.65 dia.
0.8
2.5
0.11
0.6
1.5
1.4
1.4
3.1
3.0
6.5
0.8
1.2
4.0
7.5
4.55
5.1
(F.P.)
9.0 max.
9.0 max.
(O.P.)
±0.6
6.4
2.4 max.
(P.T.)
Note: All other dimensions are the same as
those of pin plunger type.
Pretravel
2.4 max.
Movement Differential
0.7 max.
Overtravel
0.4 min.
Operating Position
6.4
±0.6
Free Position
9.0 max.
Simulated roller lever type
2.5
0.11
0.8
0.6 R
5.5
3.0
2.2 max.
(P.T.)
1.65 dia.
6.7
±0.5
(O.P.)
9.4 max.
(F.P.)
0.7
Note: All other dimensions are the same as
those of pin plunger type.
Pretravel
2.2 max.
Movement Differential
0.7 max.
Overtravel
0.3 min.
Operating Position
6.7
±0.5
Free Position
9.4 max.
1. Mounting
1) After mounting and wiring, the
insulation distance between ground and
each terminal should be confirmed as
sufficient.
2) When the operation object is in the free
position, force should not be applied to
the actuator or to the pin plunger. Also
force should be applied to the pin plunger
from vertical direction to the switch.
3) In setting the movement after
operation, the over-travel should be set
within the range of the specified O.T.
value.
4) In fastening the switch body, use the
M1.4 screw, with tightening torque of not
more than 0.098 N·m.
1) After mounting and wiring, the
insulation distance between ground and
each terminal should be confirmed as
sufficient.
2) When the operation object is in the free
position, force should not be applied to
the actuator or to the pin plunger. Also
force should be applied to the pin plunger
from vertical direction to the switch.
3) In setting the movement after
operation, the over-travel should be set
within the range of the specified O.T.
value.
4) In fastening the switch body, use the
M1.4 screw, with tightening torque of not
more than 0.098 N·m.
2. Soldering
1) Hand soldering should be
accomplished in less than 5 seconds with
an iron below 18 watts. Keep the
soldering tip temperature less than
320
1) Hand soldering should be
accomplished in less than 5 seconds with
an iron below 18 watts. Keep the
soldering tip temperature less than
320
°C. Avoid applying force to the
terminals.
2) Terminal portion must not be moved
within 1 minute after soldering. Also no
tensile strength of lead wires should be
applied to the terminals.
3) When using the angle terminal type,
insert an insulation separator between
the switch body and the printed circuit
board (Insulation separator 0.2 to 0.4mm
thick) to prevent the soldering flux from
flowing under the PC board.
2) Terminal portion must not be moved
within 1 minute after soldering. Also no
tensile strength of lead wires should be
applied to the terminals.
3) When using the angle terminal type,
insert an insulation separator between
the switch body and the printed circuit
board (Insulation separator 0.2 to 0.4mm
thick) to prevent the soldering flux from
flowing under the PC board.
3. Cleaning
As AV4 switch is not completely sealed
construction, avoid cleaning.
4. Selection of switch
When specifying AV4 switches, allow
±20% to the listed operating
characteristics.
5. Avoid using and keeping switches
in the following conditions:
• In corrosive gases
• In a dusty environment
• Where silicon atmosphere prevails
6. When switching low-level circuits
(max. 100 mA), gold plate contact
types are recommended.
7. When using the lever type, avoid
applying force from the reverse and
side direction of actuating.
As AV4 switch is not completely sealed
construction, avoid cleaning.
4. Selection of switch
When specifying AV4 switches, allow
±20% to the listed operating
characteristics.
5. Avoid using and keeping switches
in the following conditions:
• In corrosive gases
• In a dusty environment
• Where silicon atmosphere prevails
6. When switching low-level circuits
(max. 100 mA), gold plate contact
types are recommended.
7. When using the lever type, avoid
applying force from the reverse and
side direction of actuating.
Switch.book Seite 124 Donnerstag, 4. Mai 2006 10:05 10