Bicker Elektronik BICKER BEG-300-1224 300W PC-NETZTEIL BEG-300-1224 Data Sheet
Product codes
BEG-300-1224
Operating instructions
Industrial power supply
Model: BEG-300-1224
Intended use
This power supply is used for providing power to low-voltage consumers. It is a built-in unit and therefore has to be installed in a metal housing. Only
a qualified technician may install this unit.
This power supply is used for providing power to low-voltage consumers. It is a built-in unit and therefore has to be installed in a metal housing. Only
a qualified technician may install this unit.
Safety instructions
Attention, danger of life! It is strictly forbidden to modify, open, disassemble or reconvert the power supply! The BEG-300-1224 is an
enclosed power supply. Contact with the components may cause an electric shock! The following safety label is to be affixed to the
cabinet: „Before opening the cabinet, pull the mains plug!“ Any use other than described in these operating instructions may damage the
power supply and cause dangers such as short-circuit, fire etc.!
In case of damages due to disregard of these operating instructions any warranty will expire. Bicker will not be responsible for any consequential
damages! We refuse any responsibility for damages to property or persons due to inappropriate handling or disregard of these operating
instructions. Any warranty will expire!
Technical data
Before using this power supply, be sure to read the corresponding data sheet. If it is unavailable, you can read or download it in the internet under
www.bicker.de. Here you will find important information such as input voltage, output rating, operating temperature, derating, connection of earth
conductor and more. The power supply may not be operated outside of these technical data!
Before using this power supply, be sure to read the corresponding data sheet. If it is unavailable, you can read or download it in the internet under
www.bicker.de. Here you will find important information such as input voltage, output rating, operating temperature, derating, connection of earth
conductor and more. The power supply may not be operated outside of these technical data!
Installation and start-up
Only a qualified technician may install this unit. During installation the respective standards regarding electrical safety as well as the standard
EN 60950 have to be observed. Before installation, power-off the unit by switching it off and pulling the main plug.
Only a qualified technician may install this unit. During installation the respective standards regarding electrical safety as well as the standard
EN 60950 have to be observed. Before installation, power-off the unit by switching it off and pulling the main plug.
The PSU is a built-in unit and may preferably be used inside a metal housing. For the installation of the power supply suitable screws have to be used.
The power supply is a product according to protection class I. During installation a secure connection of the grounding equipment conductor
between power supply and metal housing has to be ensured. The leakage current should not exceed 3,5 mA.
Cables should be run neatly and straight. Make sure the cables are not squeezed or damaged. Protect cables against sharp edges in the housing. If
necessary, fix them using cable straps and apply a protective padding to sharp edges. Make sure the cables do not get into the computer fan.
During installation ensure that the power supply is adequately ventilated. Free circulation of air has to be possible. Also make sure that the ventilation
slots are not covered by objects, assembly parts or ribbon cables.
between power supply and metal housing has to be ensured. The leakage current should not exceed 3,5 mA.
Cables should be run neatly and straight. Make sure the cables are not squeezed or damaged. Protect cables against sharp edges in the housing. If
necessary, fix them using cable straps and apply a protective padding to sharp edges. Make sure the cables do not get into the computer fan.
During installation ensure that the power supply is adequately ventilated. Free circulation of air has to be possible. Also make sure that the ventilation
slots are not covered by objects, assembly parts or ribbon cables.
Operation
The power supply may only be operated in dry interiors. Contact with water, even by condensing air humidity, has to be avoided under any
circumstances. Operation under conditions such as extreme cold or heat, in a dusty environment and near inflammable gases, steams or solvents is
strictly forbidden as well. Always ensure an adequate ventilation.
The power supply may only be operated in dry interiors. Contact with water, even by condensing air humidity, has to be avoided under any
circumstances. Operation under conditions such as extreme cold or heat, in a dusty environment and near inflammable gases, steams or solvents is
strictly forbidden as well. Always ensure an adequate ventilation.
Derating
When operating the power supply in a higher temperature range such as +50…+70 °C the power drain has to be reduced in order to decrease the
load applied to the unit. This is not done automatically. The user himself has to take this into consideration when setting up the system and allow for
an adequate power reserve!
Example: If a 300 Watt power supply has to be operated at +60 °C operating temperature and a derating of 2.5 % / °C within the range of
+50…+70 °C is defined in the data sheet, the output load may not exceed 225 Watts.
Maintenance
The power supply does not contain any parts which need maintenance.
In case of failure, switch-off the power supply and pull the main plug.
Repairing und therefore opening of the power supply has to be done
by a qualified technician or repair shop.
When operating the power supply in a higher temperature range such as +50…+70 °C the power drain has to be reduced in order to decrease the
load applied to the unit. This is not done automatically. The user himself has to take this into consideration when setting up the system and allow for
an adequate power reserve!
Example: If a 300 Watt power supply has to be operated at +60 °C operating temperature and a derating of 2.5 % / °C within the range of
+50…+70 °C is defined in the data sheet, the output load may not exceed 225 Watts.
Maintenance
The power supply does not contain any parts which need maintenance.
In case of failure, switch-off the power supply and pull the main plug.
Repairing und therefore opening of the power supply has to be done
by a qualified technician or repair shop.
These operating instructions are a publication of Bicker Elektronik GmbH, Ludwig-Auer-Straße 23, D-86609 Donauwörth.
Errors, mistakes as well as modifications of engineering and equipment are reserved. © 14.06.2012 by Bicker Elektronik GmbH
Errors, mistakes as well as modifications of engineering and equipment are reserved. © 14.06.2012 by Bicker Elektronik GmbH
Disposal
Electrical and electronic devices may not be
disposed off with domestic waste! At the end
of its useful life, dispose of the product
according to the respective legal regulations.
Bicker Elektronik GmbH
| Ludwig-Auer-Straße 23 | 86609 Donauwörth | Germany
Tel. +49 906 70595-0 | Fax +49 906 70595-55 | info@bicker.de |
www.bicker.de