Megasat 630 T 0201024 Data Sheet
Product codes
0201024
ENGLISH
ENGLISH
14
15
Items
Features
High
Frequency
Tuner
Input Frequency Range
174 ~ 230, 470 ~~ 862MHz (VHF&UHF)
Bandwidth
7 or 8 MHz
Input Signal Level
-75 ~ -20 dBm
RF Input Connector
IEC169-2, Female
Input impedance
75 Ω
Demodu-
lation Mode
Waveform
COFDM (Code Orthogonal Frequency Division Multi-
plexing)
plexing)
Demodulation
QAM16, QAM64
Transmission Mode
2K, 8K
Guard interval
1/4, 1/8, 1/16, 1/32
Code rate
1/2, 2/3, 3/4, 5/6, 7/8
Video
Audio
Decoding
Video decoding
ISO/IEC13818-2 MPEG2 (MP@ML) Compatible
Video resolution
PAL 720×576/ NTSC 720X480
Video input code rate
15Mbit/s Max.
Teletext
Support DVB-ETS300472
Audio decoding
ISO 11172-3
Audio Track
Stereo, Monophony (Left, Right)
Audio Sample rate
32, 44.1, 48KHz
USB
USB Port
USB2.0
Format
MPEG/MP3/WMA/JPEG
Supported
SD/MMC/MS Card
Power
Voltage Range
~165-264V, 50Hz
Rated Voltage
230V,50Hz
Rated Consumption
5 W
Standby Consumption
≤ 0,5 W
Work
Environment
Temperature
0° ~ 40°
Humidity
< 90%
Dimensions
Weight
~ 0,5 kg (brutto) 0,3 kg (netto)
Size
180(W) x 113(D) x 34(H) mm
Specifications
Troubleshooting
Problem
Possible causes
What to do
LED on the front panel fail to
light up/is not lit.
light up/is not lit.
No picture or sound.
Bad picture/blocking error
No startup menu on screen after
turning on STB for the first time.
turning on STB for the first time.
The remote control is not wor-
king.
king.
Poor picture quality or Less
channels in scanning.
channels in scanning.
You have forgotten your pass-
word.
word.
Check if the main supply cable is
plugged into the power socket.
plugged into the power socket.
Adjust the dish. Check the sig-
nal strength indicator in one of
the channels search submenus.
Check the cable connections,
LNB and other equipment con-
nected to LNB & receiver, or
adjust dish. Replace the LNB.
Replace the cable.
nal strength indicator in one of
the channels search submenus.
Check the cable connections,
LNB and other equipment con-
nected to LNB & receiver, or
adjust dish. Replace the LNB.
Replace the cable.
Adjust the dish. Connect an at-
tenuator to LNB input. Change
to a larger dish. Change LNB
with lower noise factor. Replace
the LNB.
tenuator to LNB input. Change
to a larger dish. Change LNB
with lower noise factor. Replace
the LNB.
Switch the TV to the appropriate
AV input.
AV input.
Change the batteries (both).
Aim the remote control at the
STB. Check that nothing blocks
the front panel. Check if LED
indicator on the front panel is
showing the time, press the po-
wer button to switch off standby
mode.
Aim the remote control at the
STB. Check that nothing blocks
the front panel. Check if LED
indicator on the front panel is
showing the time, press the po-
wer button to switch off standby
mode.
Change the LNB power to
14V/19V in Antenna setup
menu.
14V/19V in Antenna setup
menu.
Contact the dealer or Service
Provider. They will help you set
it up again.
Provider. They will help you set
it up again.
Main supply cable is not con-
nected.
nected.
Satellite dish is not aiming to
satellite accurately. No signal or
weak signal. The LNB is faulty.
The cable is faulty.
satellite accurately. No signal or
weak signal. The LNB is faulty.
The cable is faulty.
Satellite dish is not aiming to the
satellite accurately. Signal too
strong. Satellite dish is too small.
LNB noise factor too high. The
LNB is faulty.
satellite accurately. Signal too
strong. Satellite dish is too small.
LNB noise factor too high. The
LNB is faulty.
The system is connected by
SCART cable and the TV is not in
AV/ EXT mode.
SCART cable and the TV is not in
AV/ EXT mode.
Battery exhausted. Remote con-
trol is not aimed correctly STB is
in standby mode.
trol is not aimed correctly STB is
in standby mode.
Low LNB power or signal loss in
cable.
cable.
You might meet abnormal working of this STB with various reasons. Check the following which may help you.