Megaman Decorative Lighting MM54933 Transparent MM54933 Data Sheet
Product codes
MM54933
ST01xx Series
Instruction Manual
LED STRIP
TECHNICAL SPECIFICATION
GB
Model Number
Voltage
Wattage
IP Rating
ST0103 ST0106 ST0109
Max. 4W
Max. 4W
Max. 8W
Max. 11.5W
IP20
IP20
IP20
Rated Current
DC24V
----
DC24V
----
DC24V
----
167mA
334mA
480mA
Length
310mm
610mm
910mm
ST0112
Max. 16W
IP20
DC24V
----
667mA
1210mm
ST0115
Max. 19W
Max. 19W
IP20
DC24V
----
792mA
1510mm
ST0118
Max. 24W
Max. 24W
IP20
DC24V
----
1000mA
1810mm
Correct Disposal of This Product
Item Number
MM54903
MM54913
MM54923
MM54933
MM54943
MM54953
IDV GmbH
Birkenweiherstr. 2
D-63505 Langenselbold
Germany
Birkenweiherstr. 2
D-63505 Langenselbold
Germany
www.megaman.de
8010ST002C
PART LIST
1 PCE.
180mm
Extension
Wires
Extension
Wires
End Cap
Mounting clip
1 PCE.
2 PCES.
3 PCES.
4 PCES.
5 PCES.
For 310mm to
510mm
510mm
For 610mm to
910mm
910mm
For 1010mm to
1310mm
1310mm
For 1410mm to
1810mm
1810mm
Installation
WIRING DIAGRAM
Output: 24V
Input:
220VAC-240VAC
220VAC-240VAC
Output:
DC24V
DC24V
Extension
wire
LED constant voltage driver:
Maximum length of the connected LED strip should not exceed 2 metres.
Red Cable : +ve
Black Cable : -ve
Please refer to the following diagram for the installation.
•
•
•
•
The remaining part is not recommended to use.
+ +
*
Method 1: Fasten the given mounting clips to the wall,
then fix the LED Strip to the clips.
then fix the LED Strip to the clips.
•
Open the cover of the LED Strip.
Measure and cut the LED Strip according to its cutting sign for the desired
length. A cutting sign on the LED Strip can be found at every 4.0cm.
Put the cover back to the LED Strip and cut the excess part to match with the
LED Strip.
Measure and cut the LED Strip according to its cutting sign for the desired
length. A cutting sign on the LED Strip can be found at every 4.0cm.
Put the cover back to the LED Strip and cut the excess part to match with the
LED Strip.
- -
Method 2: Install the LED Strip by using adhesive tape.
•
When the given length does not fit the requirement, please follow below instruction and cut the LED Strip to the desired length. The manufacturer accepts no liability for
any damage or out of order resulting from cutting the LED Strip inappropriately.
any damage or out of order resulting from cutting the LED Strip inappropriately.
CAUTIONS
Read the entire manual carefully before installation and operation.
Installation or replacement should be performed only by licensed and qualified
electricians.
Switch off the power source before installation, replacement and cleaning.
Before replacement of the Strip, turn it off and allow it to cool down. Heat-
resistant gloves are mandatory when handling the Strip.
The MEGAMAN LED Strip works with most conventional LED constant voltage
drivers with output voltage of DC 24V for non-dimming operation.
Installation or replacement should be performed only by licensed and qualified
electricians.
Switch off the power source before installation, replacement and cleaning.
Before replacement of the Strip, turn it off and allow it to cool down. Heat-
resistant gloves are mandatory when handling the Strip.
The MEGAMAN LED Strip works with most conventional LED constant voltage
drivers with output voltage of DC 24V for non-dimming operation.
•
•
•
•
•
•
•
Dimming feature is achievable when working with a Pulse Width Modulation
(PWM) dimming module and LED constant voltage driver with output voltage of
DC24V.
The minimum safety distance from the illuminated object is 0.1m
The manufacturer accepts no liability for any damage resulting from the misuse
of the LED Strip or from when it is used with inappropriate equipment.
Consult the dealer if you have any enquiries.
(PWM) dimming module and LED constant voltage driver with output voltage of
DC24V.
The minimum safety distance from the illuminated object is 0.1m
The manufacturer accepts no liability for any damage resulting from the misuse
of the LED Strip or from when it is used with inappropriate equipment.
Consult the dealer if you have any enquiries.
•
Instant start is allowed.
Recommended operating temperature is -30°C to +40°C.
The maximum length of the connected LED Strip should not exceed 2 metres
The maximum length of the connected LED Strip should not exceed 2 metres
Designed for indoor application.
ATTENTION
•
•
•
•
•
•
•
and the total wattage of the connected LED Strip should not exceed 26W.
The total wattage of the connected LED Strip should not exceed the maximum
load of the LED constant voltage driver.
The total wattage of the connected LED Strip should not exceed the maximum
load of the LED constant voltage driver.
•
0.1m
---
•
This marking indicates that this product should not be disposed with other household wastes
throughout the EU. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material
resources. To return your used device, please use the return and collection systems or contact
the retailer where the product was purchased. They can take this product for environmental safe
recycling.
throughout the EU. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material
resources. To return your used device, please use the return and collection systems or contact
the retailer where the product was purchased. They can take this product for environmental safe
recycling.
•