Wera LED outdoor wall light 3 W Warm white 13801 Anthracite 13801 Data Sheet

The product is intended to provide outdoor lighting. The product is intended for mounting on 
a vertical wall.
The safety instructions must be observed at all times!
Any use other than that described above could lead to damage to this product and involves 
the risk of short circuits, fi re, electric shock, etc. No part of the product may be modifi ed or 
converted!
This product complies with the applicable national and European requirements. All names of 
companies and products are the trademarks of the respective owners. All rights reserved.

•  LED outdoor wall light
•  Mounting material (screws, wall plugs)
• Operating instructions

 

 

This symbol indicates a health hazard, e.g. electric shock.

 

 The icon with an exclamation mark indicates particular dangers associated with 
handling, function or operation. 

  The “Hand” symbol indicates special tips and operating information.

  The product cannot be dimmed.

  Observe the operating instructions!

   Read the complete operating manual carefully before using the product, as it 

 If you do not have the expertise required for the installation, do not install it 
yourself but entrust the work to a qualifi ed electrician. 

 

•  Unauthorised conversion and/or modifi cation of the product is not allowed for 

safety and approval reasons (CE).

 

•  The product is not a toy and should be kept out of the reach of children. There is 

danger of a life-threatening electric shock!

 

•  If it can be assumed that safe operation is no longer possible, the device must be 

turned off (take out corresponding fuse or switch off automatic cut-out; switch off 
corresponding ground fault circuit interrupter) and precautions are to be taken to 
ensure that it is not used unintentionally. After this, arrange for an expert to check 
the product.

 

  Safe operation can no longer be assumed if:

 

  - the device shows visible signs of damage,

 

  -  the product does not work at all or works poorly (where there is fl ickering light, 

leaking smoke or a smell of burning, audible crackling noises, or discolouration 
to the product or to adjacent surfaces)

 

  - the product was stored under unfavourable conditions

 

  - it was exposed to heavy loads during transport

  •  Never direct a jet of water (e.g. for cleaning) from a garden hose or high-pressure 

cleaner, or similar source, onto the product!

 

• Caution, LED light: 

 

  Do not look directly into the LED light!

 

  Do not look into the beam directly or with optical instruments! 

 

•  Do not leave packaging material carelessly lying around, since it could become a 

dangerous plaything for children.

 

•  The accident prevention regulations of the association of compensation insurers 

must be followed when using all electrical facilities and equipment in commercial 
locations.

 

•   If you have any questions that are not answered in this manual, please contact our 

technical service or another specialist.

 

•  The product is protected according to IP44; it can be mounted and operated in-

doors and outdoors. Pay attention to the correct mounting position; see chapter 
“Connection and mounting”. 

 

   The product is suitable for use outdoors; however, it must never be used in or 

under water! 

 

•  Only use the product when it is securely installed and steady.

 

•  When installing, make sure that the connecting cable is not kinked, pinched or 

damaged by sharp edges. 

 

•   Do not use this product in rooms or under adverse environmental conditions where 

combustible gases, vapours or dust are or may be present! There is a risk of explo-
sion!

 

•  Handle the product with care; it has sharp edges.

 

•  The product must not be exposed to extreme temperatures, strong vibrations or 

heavy mechanical stress.

 

•  Do not attach any items (e.g. decorations) to the product; there is a risk of fi re!

 

•  The product may be operated only on the mains voltage (see section “Technical 

Data”). Never try to operate the device using any other voltage.

 

   During installation, all poles must be disconnected from the mains voltage (e.g. via 

RCD). 

 

•  The product is designed according to Protection Class I; the protective earth con-

ductor must be connected. 

 

   If there is not a mains supply provided with a protective earth conductor at the 

place of installation, the product must not be connected/used there. In this case, 
install a new voltage supply with a protective earth wire.

 

•  Connection is allowed only under zero-voltage conditions. First switch off all poles 

of the mains supply by removing the fuse or switching off at the circuit breaker; 
then also switch off the associated residual current circuit breaker. Secure it 
against unauthorised reconnection, e.g. with a danger sign. Check the mains con-
nection for absence of voltage using a suitable tester.

 

• The product cannot be dimmed.

 

•  Make sure that all electrical connections and connection cables correspond to the 

regulations and to their operating instructions. 

•   Without fail, pay attention to the correct mounting position 

for the LED outdoor wall light; it must only be mounted so 
the light points downwards. 

  Please note the illustration at right for this. 
•   Make sure you install the LED outdoor wall light only on a 

solid base, e.g. brickwork. Use screws and, if necessary, 
screw anchors that are suitable for the surface.

•   The LED outdoor wall light must be installed and used out of the reach of children.
•   Select the mounting height depending on the on-site conditions. We recommend a mounting 

height of approx. 1.5 – 2 m.

•   The LED outdoor wall light must be secured on the user’s distribution board by a 10/16A fuse. 

An earth circuit fault interrupter must be installed before this (FI protective switch).

•   The LED outdoor wall light must be current/voltage-free during installation. It is not suffi cient 

to just turn off the light switch!

   First switch off all poles of the mains supply by removing the fuse or switching off at the circuit 

breaker; then also switch off the associated residual current circuit breaker. Secure it against 
unauthorised reconnection, e.g. with a danger sign.

•   Check the mains connection for absence of voltage using a suitable meter.