Wera LED outdoor free standing light (+ motion detector) 3.84 W Warm white 12537-600 Anthracite 12537-600 Data Sheet

•  If it is no longer possible to operate the product safely, take it out of operation and 

protect it from any accidental use. Safe operation can no longer be guaranteed if 

the product:

 - is visibly damaged, 
 - is no longer working properly, 
 - has been stored for extended periods in poor ambient conditions or 
 - has been subjected to any serious transport-related stresses.

•  Please handle the product carefully. Jolts, impacts or a fall even from a low height 

can damage the product.

•  For installations in industrial facilities, follow the accident prevention regulations 

for electrical systems and equipment of the government safety organization or the 

corresponding authority for your country.

 

•  Consult an expert when in doubt about operation, safety or connection of the 

device.

•  Maintenance,  modifications  and  repairs  are  to  be  performed  exclusively  by  an 

expert or at a qualified shop.

•  If you have questions which remain unanswered by these operating instructions, 

contact our technical support service or other technical personnel.

•  The PIR sensor integrated in the product responds to temperature changes within the 

detection range. Such is the case when humans or animals, whose temperatures differ from 

the ambient temperature, enter the detection range.

•  In order to allow for maximum detection, the product should be positioned in such a way that 

the object to be detected does not walk towards the motion detector but crosses the detection 

range from left to right or vice versa. Keep that in mind when installing the product.

•  The range of detecting temperature changes depends on a variety of factors:

 - Installation height
 - Ambient temperature
 - Temperature difference between the moving object and the environment
 - Size of the object
 - Distance between object and product
 - Direction and speed of motion

Detecting temperature changes through glass is basically not possible. Do not 

install the product behind a pane of glass.

•  The product is suitable for use in unprotected outdoor areas. It must however not be used in 

or under water. This poses a risk of fatal injury due to electric shock!

•  Do not expose the product to salt water (e.g. road salt during winter months), as this could 

cause corrosion.

•  Mount the product to a horizontal surface only. 
•  Do not mount the product to or inside vehicles.
•  When mounting the product, take into consideration the routing of the mains cable.
•  Only use a suitable, fixed mains cable for power supply.
•  The product must be secured via an existing sub-distribution unit with a 10/16A fuse. This 

setup requires the installation of an upstream residual current circuit breaker (FI switch).

•  The product must be completely free of voltage for installation. Just turning off the light via the 

switch does not make it entirely voltage-free.

•  Turn off the corresponding circuit breaker and/or automatic fuse to remove all voltage from 

the power circuit. Secure them against unauthorized restart, e.g. by installing a warning sign. 

Also switch off the relevant circuit breaker in order to disconnect all poles of the mains cable 

from the mains supply.

•  Check the power circuit for any remaining voltage using an appropriate measuring device.

The product is suitable for outdoor installation (protection type IP54) and is intended for lighting 

entrance areas, patios, etc. The product contains a PIR sensor type motion detector.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you 

use the product for purposes other than those described above, the product may be damaged. 

In addition, improper use can cause hazards such as short circuiting, fire, electric shock etc. 

Read the instructions carefully and keep them. Make this product available to third parties only 

together with its operating instructions.
This product complies with the statutory national and European requirements. All company 

names and product names are trademarks of their respective owners. All rights reserved.

•  Outdoor floor lamp
•  Mounting material (4 x screw, 4 x dowel)
•  Operating instructions

The triangle containing a lightning symbol warns against danger of electric shock or 

impairment of the electrical safety of the device.

An exclamation mark in a triangle indicates important notes in these operating 

instructions that must be strictly observed.

The “hand” symbol indicates special information and advice on operation.

Protection type IP54 (splash-proof): The product is suitable for outdoor use.

Follow all instructions in the operating instructions.

•  The device is not a toy. Keep it out of the reach of children and pets. This poses a 

risk of fatal injury due to electric shock!

•  Do not leave packaging material lying around carelessly. These may become 

dangerous playing material for children.

•  Operate the product only via a common household power supply of 

 

220 – 240 V/AC, 50/60 Hz.

•  The product is only suitable for fixed installation.
•  The product must not be installed in flood-prone areas. The same applies to areas 

(e.g. depressions) in which rainwater could accumulate.

•  Never point a garden hose at the product.
•  The product may not be mounted in or under water.
•  Attention, LED light:

 - Do not look directly into the LED light!
 - Do not look into the beam directly or with optical instruments!

•  Protect  the  product  from  extreme  temperatures,  strong  jolts,  flammable  gases, 

vapours and solvents.

•  Do not place the product under any mechanical stress.