Brinno PHV132514 Data Sheet

The spy hole monitor is able to better identify visitors arriving at your front door. The product is 
intended for dry indoor use only. Power is supplied via 2 x 1.5 V batteries (type: AA/mignon). Do 
not use any other source of energy. The correct battery type is specifi ed under "Technical Data".

Any use other than the one described above is inadmissible and damages this product. Moreo-
ver, this involves dangers, e.g. short-circuit, fi re etc.

All safety instructions and notes on operation in these operating instructions must be observed 
at all times. These instructions not only protect the device but also and in particular your health. 
Please read through the operating instructions carefully before using the product. Keep them in 
a safe place for future reference.

This product complies with the applicable national and European specifi cations. All company 
names and product names are trademarks of their respective owners. All rights reserved.

•  Spy hole monitor
•  Clamp screw
•  Flange
•  Spy hole (lens and bushing)
•  Tightening wrench
•  2 x 1.5 V batteries (type: AA/mignon)

Hazard warnings and signs are clearly marked in the operating instructions. The following sym-
bols are used:

The symbol with the exclamation mark inside the triangle indicates particular haz-
ards during handling, operation or control.

 

☞

This symbol denotes information provided to improve understanding of the proce-
dures.

•  For reasons of safety and approval (CE), the device must not be converted and/

or modifi ed without authorisation.

•  If you have any doubts about the correct operation or the safety of the product, 

please consult a specialist.

•  The product is intended for dry indoor use only.
•  Handle  the  product  with  care.  It  can  be  damaged  by  impact,  blows  or  when 

dropped even from a low height.

•  The product is not a toy and should be kept out of the reach of children. Particu-

lar care must therefore be exercised if children are around.

•  Do not leave any packaging material unattended. It may become a dangerous 

toy for children.

•  Please observe the correct polarity (positive/+ and negative/-) when inserting 

the batteries.

•  Keep batteries/rechargeable batteries out of the reach of children.
•  Do not leave any batteries/rechargeable batteries lying around. There is a risk 

of batteries being swallowed by children or pets. If swallowed, consult a doctor 
immediately.

•  Leaking  or  damaged  batteries/rechargeable  batteries  may  cause  acid  burns 

if allowed to come into contact with the skin. Wear suitable protective gloves.

•  Make sure that batteries/rechargeable batteries are not short-circuited, disman-

tled or thrown into fi re. There is a danger of explosion!

•  Do not recharge normal batteries. There is a danger of explosion! Only charge 

rechargeable batteries intended for this purpose; use a suitable battery charger.

•  If you do not intend to use the product for a prolonged period (e.g. storage), re-

move the inserted batteries/rechargeable batteries. Old batteries can leak and 
damage the device. This will invalidate the warranty/guarantee.

•  Always  replace  the  whole  set  of  batteries/rechargeable  batteries.  Only  use 

batteries/rechargeable batteries of the same type/manufacturer with the same 
charge  state  (do  not  combine  full  with  semi-charged  or  empty  batteries/re-
chargeable batteries).

•  Never  combine  batteries  and  rechargeable  batteries!  Use  either  batteries  or 

rechargeable batteries.

•  Please read the chapter "Disposal" to ensure that the batteries and recharge-

able batteries are disposed of without damaging the environment.

1.  Spy hole monitor
2.  Clamp screw
3.  ON/OFF button
4.  Battery check LED

5.  Battery compartment lid

6.  Spy hole bushing
7.  Flange
8.  Door hole (inside)
9.  Door hole (outside)
10. Spy hole lens

•  Turn the fl ange (7) on the back of the product by 25 degrees to the left (anticlockwise) and 

remove. Undo the clamp screw (2) beforehand if necessary

•  Open the battery compartment (5) on the back of the product.
•  Insert two AA/mignon type batteries into the battery compartment, observing the correct polar-

ity (see stamp in battery compartment)

•  Close the battery compartment again
•  Unscrew the spy hole bushing (6) from the spy hole lens (10)
•  Replace the old spy hole with the new spy hole lens (10) on the outside of the door

 

☞

If there is no spy hole, drill a hole with a 12 mm diameter at eye level. The thickness 
of the door must not exceed 35 to 57 mm.

•  Push  the  spy  hole  bushing  (6)  through  the  fl ange  (7)  and  then  the  spy  hole  bushing  (6) 

through the door hole (8) on the inside of the door

•  Hand-tighten the spy hole bushing (6) with the spy hole lens (10)

 

☞

As soon as the bushing is tight, turn the fl ange (7) until the "TOP" symbol is pointing 
upwards.

•  Now tighten the spy hole bushing (6) using the tightening wrench supplied
•  Turn the spy hole monitor (1) anticlockwise until it is positioned on the fl ange (7) at 25 degrees
•  Now turn the spy hole monitor (1) anticlockwise until you feel it engage
•  Tighten the clamp screw (2) using the screwdriver