Graupner Hendheld RC 2.4 GHz No. of channels: 5 33110 User Manual
Product codes
33110
105
Program description: base settings - fi xed-wing model
„Delta/FW“:
The aileron and elevator rudder is
controlled by one servo per wing half,
connected on channel 2 and 3. The cou-
pling function for the aileron and elevator
control is performed automatically by the
transmitter mixer.
controlled by one servo per wing half,
connected on channel 2 and 3. The cou-
pling function for the aileron and elevator
control is performed automatically by the
transmitter mixer.
The jumper connects the two right pins
„DELTA“.
„DELTA“.
„V-Tail“:
The elevator and rudder functions are
operated by two control surfaces set in a
V-shape, each controlled by a separate
servo, connected to channel 2 and 3. The
two-way coupling function for the rudder
and elevator control systems is automati-
cally carried out by the transmitter soft-
ware.
operated by two control surfaces set in a
V-shape, each controlled by a separate
servo, connected to channel 2 and 3. The
two-way coupling function for the rudder
and elevator control systems is automati-
cally carried out by the transmitter soft-
ware.
Two jumpers connect the two left „AILE“
and two right „DELTA“ pins.
and two right „DELTA“ pins.
Notes:
During the programming process it is important
•
to ensure that any internal-combustion engine or
electric motor cannot start running accidentally.
The safe option is always to disconnect the fuel
supply or the fl ight battery.
electric motor cannot start running accidentally.
The safe option is always to disconnect the fuel
supply or the fl ight battery.
Tail type
The tail confi guration is chosen with the supplied jumper
in the contact strip „MIX“ on the front of the transmitter.
Select the positioning of the jumpers to match your
model type
in the contact strip „MIX“ on the front of the transmitter.
Select the positioning of the jumpers to match your
model type
„normal“:
The elevator and rudder is operated by
only one servo.
only one servo.
The jumper connects the two middle pins
„NO MIX“.
„NO MIX“.
„2 Aileron“:
This
option is for models with 1 or 2 ailerons.
The at the channel 5 connected servo
runs parallel to the servo on channel 2
The Aileron trim affects both servos.
The at the channel 5 connected servo
runs parallel to the servo on channel 2
The Aileron trim affects both servos.
The jumper connects the two left pins
„AILE“.
„AILE“.
Due to the different installation of the servos and push-
rods the initially servo direction of certain servos may
be wrong. The following table provides guidance for
remedial action.
rods the initially servo direction of certain servos may
be wrong. The following table provides guidance for
remedial action.
Model
type
Servo with
wrong
rotating direction
Solution
V-Tail
Rudder and
elevator wrong
direction
elevator wrong
direction
servo reverse for
channel 3 + 4 in the bar
„Servo reverse“
channel 3 + 4 in the bar
„Servo reverse“
Rudder correct,
elevator wrong
direction
elevator wrong
direction
change servo 3 + 4 at
the receiver
the receiver
Elevator correct,
rudder wrong
direction
rudder wrong
direction
servo reverse for
channel 3 + 4 in the bar
„Servo reverse“ AND
change at the receiver
channel 3 + 4 in the bar
„Servo reverse“ AND
change at the receiver
Delta,
Flying
wing
Flying
wing
Elevator and Ail
wrong direction
wrong direction
servo reverse for
channel 2 + 3 in the bar
„Servo reverse“
channel 2 + 3 in the bar
„Servo reverse“
Elevator correct, Ail
wrong direction
wrong direction
servo reverse for
channel 2 + 3 in the bar
„Servo reverse“ AND
change at the receiver
channel 2 + 3 in the bar
„Servo reverse“ AND
change at the receiver
Ail correct, Elevator
wrong direction
wrong direction
change servo 2 + 3 at
the receiver
the receiver