Jeti Hendheld RC 2.4 GHz No. of channels: 8 80001585 User Manual
Product codes
80001585
computer radio control system
EN
5.
The„Functions Assignment“ menu lists
the flight functions and their control
switch/stick assignments. If you want to
change any of the switch/stick assign-
ments, select the „Control“ item for your
flight function and then select your desired
switch/stick for that flight function. Press
„F5(Next)“ to confirm.
switch/stick assignments. If you want to
change any of the switch/stick assign-
ments, select the „Control“ item for your
flight function and then select your desired
switch/stick for that flight function. Press
„F5(Next)“ to confirm.
When you create a new helicopter model, you are required to define
the swash plate configuration for the model. Please refer to your
helicopter’s instructions and verify that you have the correct swash
plate configuation. If you find that you need to change your swash
plate configuration, you can always go to the „Model -> Basic
Properties“ menu to make the change.
the swash plate configuration for the model. Please refer to your
helicopter’s instructions and verify that you have the correct swash
plate configuation. If you find that you need to change your swash
plate configuration, you can always go to the „Model -> Basic
Properties“ menu to make the change.
6.
The „Servo assignment“ menu displays
the receiver channels and their transmitter
output assignments. If you want to change
any of the output assignments, select the
channel you want to edit and reassign its
output. Otherways press „F5(Next)“ to
confirm.
output assignments. If you want to change
any of the output assignments, select the
channel you want to edit and reassign its
output. Otherways press „F5(Next)“ to
confirm.
7.
The „Swash Mix“ menu displays the travel
range of each particular helicopter flight
function for the swash plate. The travel
range is displayed as a percentage. You can
use these travel range adjustments to
prevent linkage binding and to tune the
helicopter to suit your flying style. You can
function for the swash plate. The travel
range is displayed as a percentage. You can
use these travel range adjustments to
prevent linkage binding and to tune the
helicopter to suit your flying style. You can
8.
The screen will display a question which
asks if you really want to create and activate
the new model. Press the „F5(Yes)“ button
to confirm.
the new model. Press the „F5(Yes)“ button
to confirm.
9.
The „Servo Setup“ menu is where you
can set all of your servo neutral positions,
servo output throw limits, servo reversing,
delay etc. You should return to this menu
after you have bound your receiver and
transmitter. See chapter 8.4: Receiver-
>Binding.
servo output throw limits, servo reversing,
delay etc. You should return to this menu
after you have bound your receiver and
transmitter. See chapter 8.4: Receiver-
>Binding.
3.
3.
also activate a cyclic reduction of the rotor head travels (Swash Ring)
so the servos cannot be damaged by large simultaneous movements
of the sticks.(Refer to your helicopter’s instruction manual.) Press the
„F5(Next)“ button to confirm.
so the servos cannot be damaged by large simultaneous movements
of the sticks.(Refer to your helicopter’s instruction manual.) Press the
„F5(Next)“ button to confirm.
10.
Once your transmitter has been bound with a receiver and has
been connected to its power supply, the last step consists of tuning
the servo output functions, see chapter 7.3.4: Setup of receiver
outputs.
In the „Fine tuning -> Flight modes“ menu you will setup these
advanced model control functions for your helicopter:
Collective pitch curve, see: Fine tuning -> Flight Modes->Function
Curves
Throttle curve, see: Fine tuning -> Flight Modes->Function Curves
the servo output functions, see chapter 7.3.4: Setup of receiver
outputs.
In the „Fine tuning -> Flight modes“ menu you will setup these
advanced model control functions for your helicopter:
Collective pitch curve, see: Fine tuning -> Flight Modes->Function
Curves
Throttle curve, see: Fine tuning -> Flight Modes->Function Curves
50