Jeti Hendheld RC 2.4 GHz No. of channels: 8 80001585 User Manual
Product codes
80001585
computer radio control system
EN
8 Receiver
3.
3.
1.
JETI Duplex receivers use the universal or „JR Type“ servo
connectors.
2.
Bat - receiver and servo power supply input. Whenever
possible, always supply power to your receiver using more than one
of these inputs. You can either supply power through the use of a Y-
cable or through any unused receiver channel connection. To power
the receiver you may use NiCd packs, the BEC from your ESC or Li-xx
cells used with a voltage regulator, such as the JETI MAXBEC or
similar.
of these inputs. You can either supply power through the use of a Y-
cable or through any unused receiver channel connection. To power
the receiver you may use NiCd packs, the BEC from your ESC or Li-xx
cells used with a voltage regulator, such as the JETI MAXBEC or
similar.
3.
SAT - auxillary input/output for PPM signals. This input allows
you to connect an additional JETI DUPLEX Rsat2 satellite receiver or
an additional US version Duplex receiver.This allows you to increase
the number of receiver antennas in your system for increased
reliabilty in installations with shielded or badly oriented antennas.
an additional US version Duplex receiver.This allows you to increase
the number of receiver antennas in your system for increased
reliabilty in installations with shielded or badly oriented antennas.
4.
EXT - input for telemetry sensors. If you want to connect more
than one telemetry sensor then use the JETI EXPANDER E4. You can
„daisy-chain“ several of the E4 Expanders to support many, many
sensors.
„daisy-chain“ several of the E4 Expanders to support many, many
sensors.
8.1 Description
1
5
4
3
2
5.
A1/A2 - receiver antennas. The antennas should be installed
so that the wires form a 90° angle relative to each other.
8.2 Installation
Whenever possible, you should wrap the receiver in foam and place
it as far as possible from sources of interference (servos, electric
motors). Arrange the receiver antennas so that their active ends form
a 90° angle and try to put them as far as possible away from each
other. Take care not to bend them with a radius smaller than 1 cm.
The active part of the antenna should not be placed close to metal
parts. If your model has a carbon fuselage it is very important to
place the active antenna ends outside the fuselage.
it as far as possible from sources of interference (servos, electric
motors). Arrange the receiver antennas so that their active ends form
a 90° angle and try to put them as far as possible away from each
other. Take care not to bend them with a radius smaller than 1 cm.
The active part of the antenna should not be placed close to metal
parts. If your model has a carbon fuselage it is very important to
place the active antenna ends outside the fuselage.
8.3 Binding
In order to achieve communication between transmitter and
receiver you must bind them. During this process the transmitter
learns the receiver address and will automatically find it again when
switched back on. Communication begins with this receiver
automatically if the transmitter is not already communicating with
another receiver. The binding process needs only to be done once
for each receiver.
receiver you must bind them. During this process the transmitter
learns the receiver address and will automatically find it again when
switched back on. Communication begins with this receiver
automatically if the transmitter is not already communicating with
another receiver. The binding process needs only to be done once
for each receiver.
8.3.1 Standard pairing procedure
1.
Switch off the transmitter and receiver.
2.
Plug the „BIND PLUG“ into the EXT receiver input.
3.
Connect receiver power supply.
4.
Switch on the transmitter. The receiver will bind with the
primary transmitter module.
55