Jeti Hendheld RC 2.4 GHz No. of channels: 8 80001585 User Manual
Product codes
80001585
computer radio control system
EN
If you would like to make set-up changes in an existing
model, you should first make a copy of the original
setup. This will help you if you would like to return to the
original model setup.
model, you should first make a copy of the original
setup. This will help you if you would like to return to the
original model setup.
Note:
Try to arrange your most frequently used models at
the beginning of the model list in order to avoid having
to browse the whole list when selecting a model.
the beginning of the model list in order to avoid having
to browse the whole list when selecting a model.
Note:
name, press the „F5(Ok)“ button to continue. Your model copy will
appear at the end of your model list.
appear at the end of your model list.
9.1.2 New Model
Selecting this menu item starts the new model creation assistant.
The assistant begins creating a new model profile as soon as you
select „New model“. However, the new model will only be created
after the confirmation in the last assistant menu, „Servo
Assignment“. Until you make the final confirmation, the new model
is NOT created or stored in the memory.
The setup possibilities of the DC/DS transmitters are very extensive.
For simplicity, some of the possible adjustments are accessible only
for certain combinations of wing and tail arrangements,
aerodynamic brakes, landing gears, and number of motors or
engines.
The assistant begins creating a new model profile as soon as you
select „New model“. However, the new model will only be created
after the confirmation in the last assistant menu, „Servo
Assignment“. Until you make the final confirmation, the new model
is NOT created or stored in the memory.
The setup possibilities of the DC/DS transmitters are very extensive.
For simplicity, some of the possible adjustments are accessible only
for certain combinations of wing and tail arrangements,
aerodynamic brakes, landing gears, and number of motors or
engines.
For safety, start creating a model with the receiver in the model
switched off. Be careful when handling electric models or servo
binding, where an improper linkage connection may cause
damage when power is applied. When handling electric models
it is safer to remove the propeller or disconnect the motor during
model creation and tuning.
switched off. Be careful when handling electric models or servo
binding, where an improper linkage connection may cause
damage when power is applied. When handling electric models
it is safer to remove the propeller or disconnect the motor during
model creation and tuning.
Note:
1.
Model name
Use the „3D Control Selector“ to select the model name menu. You
4.
4.
1
2
If you would like to copy a model from one transmitter to
another you should notice that the transmitters may not
have the same software equipment, so the configuration
of activated modules may not match each other. In this
case it is necessary to check the individual functions of
the model, since an attempt to load the model file by
another transmitter may end up with an error message
(see System -> Installed Modules).
another you should notice that the transmitters may not
have the same software equipment, so the configuration
of activated modules may not match each other. In this
case it is necessary to check the individual functions of
the model, since an attempt to load the model file by
another transmitter may end up with an error message
(see System -> Installed Modules).
Note:
3.
Deleting a Model
A model can be removed from the memory. In the model list select
the model you want to delete and press the „F5(Delete)“ button. For
safety reasons it is impossible to delete the currently selected model.
the model you want to delete and press the „F5(Delete)“ button. For
safety reasons it is impossible to delete the currently selected model.
4.
Choice of model sequence
The sequence of models can be changed by using the „F1()“ button
to move the selected model one position downwards or by using the
„F2()“ button to move the model one position upwards. The
transmitter allows storing of many models in the memory.
to move the selected model one position downwards or by using the
„F2()“ button to move the model one position upwards. The
transmitter allows storing of many models in the memory.
70