Shuttle XS36V Data Sheet
__p
XS36V4 Series Quick Guide【English】
Front Panel
Back Panel
F1. Power Button
F2. Power LED
F3. HDD LED
F4. Serial Ports (COM1,COM2)
F5. SD Card Reader
F6. USB 2.0 Port
F7. Vertical Stand
F2. Power LED
F3. HDD LED
F4. Serial Ports (COM1,COM2)
F5. SD Card Reader
F6. USB 2.0 Port
F7. Vertical Stand
Connecting the System
5
Connecting Power
1
Connecting Monitor or LCD TVs
Digital and analog connections are available so the device can be
connected to computer monitors, flat-panel displays, plasma or LCD TVs.
2
Connecting Keyboard/Mouse or USB Devices
3
Connecting LAN
4
Connecting Speakers and Microphones
6
Powering on the system
Digital: Connect a computer monitor or TV device to the HDMI port.
D-Sub Port
D-Sub Cable
Display with D-Sub input
Display with HDMI input
HDMI Port
HDMI Cable
LAN Port
RJ45 Cable
Wall
Internet
DSL/Cable Modem
USB Ports
USB Devices
USB Keyboard/Mouse
Microphone,
Headphone/Line-out Jack
Microphone/Headphone
Speakers
Power Jack (DC-in)
53R-XS36V3-2901
L
The product’s colour and specifications may vary from the actually shipping product.
A. Begin Installation
1. Undo one screw of the chassis cover.
2. Slide the cover backwards and upwards.
2. Slide the cover backwards and upwards.
For safety reasons, please ensure that the power cord is disconnected before
opening the case.
B. Memory Module Installation
1. Locate the SODIMM slot on the mainboard.
2. Align the notch of the memory module with
2. Align the notch of the memory module with
the one of the memory slot.
3. Gently insert the module into the slot in a 45-degree angle.
4. Carefully push down the memory module until it snaps into the locking mechanism.
4. Carefully push down the memory module until it snaps into the locking mechanism.
SODIMM slot
Screw
2
1
C. HDD Installation
2. As shown, install the HDD & bracket in the chassis and push it towards the direction as
indicated by the red arrow to connect the HDD connector.
HDD Connector
1. Mount the HDD into the bracket with four screws.
3. Tighten the HDD & bracket with
three screws.
1. Replace the cover and refasten one screw.
2. Tear off the double sided protective membrane.
2. Tear off the double sided protective membrane.
D. Complete
Using the Vertical Stand
Install the vertical stand and check that it is properly aligned, then tighten securely with
one screw.
Screw
Screw
Vertical Stand
1
2
Safety Information
Read the following precautions before setting up a Shuttle PC.
CAUTION
Incorrectly replacing the battery may damage this co-mputer.Replace only with the
Incorrectly replacing the battery may damage this co-mputer.Replace only with the
same or equivalent type recommended by the manufacturer. Disposal of used batteries
according to the manufacturer's instructions.
F4
F5
F7
F1
F2
F3
F4
F6
1
2
3
B1. Microphone Jack
B2. Headphone/Line-out Jack
B3. LAN Port
B4. Kensington Lock
B5. USB 3.0 Port
B6. USB 2.0 Ports
B7. HDMI Port
B8. D-Sub (VGA) Port
B9. Display Port
B10. Power Jack (DC-in)
B2. Headphone/Line-out Jack
B3. LAN Port
B4. Kensington Lock
B5. USB 3.0 Port
B6. USB 2.0 Ports
B7. HDMI Port
B8. D-Sub (VGA) Port
B9. Display Port
B10. Power Jack (DC-in)
B2
B1
B3
B4
B6
B8
B5
B9
B7
B10
Latch
Latch
45-degree
angle
2
1
3
Display Port Connector
Display Port
Display Port Cable
Digital: Connect a computer monitor or TV device to the Display Port.
Jumper for COM Port Voltage Setting (JP2)
1
1
1
0V
12V
5V
Cutout
Notch
XS36V4 default BIOS is for use with 64bit operating systems only.
A 32bit BIOS can be downloaded from the Shuttle website, if required.
Analog: Connect your computer monitor or LCD TV to the D-Sub Port.
1
2
2
1
3
5
4
This mainboard does only support 1.35V DDR3L memory moudles.