Kaercher Steam cleaner Kärcher SC3 Premium 1.513-050.0 1900 W White, Grey 1.513-050.0 Data Sheet

 It is recommended to sweep or vacuum the floor prior 
to using the steam cleaner. This way, the floor is already 
cleared of dirt/loose particles prior to the wet cleaning.

Prior to treatment with the steam cleaner, always check 
the reaction of the textiles in an inconspicuous location: 
Steam at first, then let dry and then check for colour or 
shape changes.

When cleaning painted or plastic-coated surfaces, as 
found on kitchen and living room furniture, doors, par-
quet; wax, furniture polish, plastic surfaces or paint can 
come loose or stains can be created. When cleaning 
these surfaces, briefly steam a cloth and wipe the sur-
faces with it.
ATTENTION
Never direct the steam jet at glued edges as the edge 
band may loosen. Do not use the steam cleaner on un-
sealed wooden or parquet floors.

In case of low outside temperatures, especially in the 
winter, warm up the window pane by slightly steaming 
the entire glass surface. This will prevent tensions on 
the surface which might lead to glass breakage.
Then clean the window surface with the hand nozzle 
and attachment. Use a squeegee to remove the water 
or wipe the surfaces dry. 
ATTENTION
Do not direct steam onto the sealed locations of the win-
dow frame to prevent damage.

You can use the steam gun without any additional ac-
cessories, e.g.:
–

to remove light wrinkles from hanging clothes by 
steaming them at a distance of 10 to 20 cm.

–

to remove dust from plants. Here, keep a distance 
of 20-40 cm.

–

for moist dusting, by briefly steaming the cloth and 
wiping the furniture with it.

The closer this nozzle is to the contaminated area, the 
higher the cleaning effect, as the temperature and the 
steam are highest at the nozzle output. Especially suit-
ed for cleaning difficult access locations, joints, fittings, 
drains, sinks, toilets, blinds and heaters. Heavy lime 
scale can be drenched in vinegar prior to steam-clean-
ing. Let the vinegar penetrate for about 5 minutes.

The round brush can be installed onto the detail nozzle 
as an accessory. Attached brushes can therefore be 
used to remove heavy soiling.
ATTENTION
Not suitable for cleaning sensitive surfaces.
Illustration 


Attach the round brush to the detail nozzle.

The power nozzle can be installed onto the detail nozzle 
as an accessory. 
The power nozzle increases the emission speed of the 
steam. Therefore, it is well-suited for cleaning very 
tough dirt, blowing out corners, grooves, etc.
Illustration 


Attach the power nozzle to the detail nozzle ac-
cording to the round brush.

The round brush can be installed onto the detail nozzle 
as an accessory. This round brush allows to clean large 
rounded surfaces (e.g. sink, shower tray, bathtub, kitch-
en sink).
ATTENTION
Not suitable for cleaning sensitive surfaces.
Illustration 


Attach the round brush to the detail nozzle.



Install hand nozzle on steam gun.

Illustration 
Pull the cloth cover over the hand nozzle. Especially 
well-suited for small washable areas, shower stalls and 
mirrors.

Suited for all washable walls and floor coverings, e.g. 
stone floors, tiles and PVC floors. Work slowly on very 
dirty surfaces to allow the steam to act on the dirt for a 
longer period of time.
Note
Detergent residue or care emulsions that are still pre-
sent on the surface to be cleaned can lead to streaks 
during steam cleaning. However, these will disappear 
with repeated cleaning procedures.
Illustration 


Attach the floor cloth to the floor nozzle.

1

Place the floor nozzle on top of the floor cloth.
Depending on model - fold bevore the floor cloth 
the long way.

2

Open holding clamps.

3

Place the cloth ends into the openings.

4

Close the holding clamps.

몇 CAUTION

Illustration 


During work breaks, hook the floor nozzle into the 
parking holder.