Wera LED outdoor free standing light 7.2 W Warm white 13802-850 Anthracite 13802-850 Data Sheet

•  Please handle the product carefully. Jolts, impacts or a fall even from a low height

can damage the product.

•  For installations in industrial facilities, follow the accident prevention regulations

for electrical systems and equipment of the government safety organization or the

corresponding authority for your country.

•  Consult  an  expert  when  in  doubt  about  operation,  safety  or  connection  of  the

device.

•  Maintenance,  modifications  and  repairs  are  to  be  performed  exclusively  by  an

expert or at a qualified shop.

•  If you have questions which remain unanswered by these operating instructions,

contact our technical support service or other technical personnel.

•  The product is suitable for use in unprotected outdoor areas. It must however not be used in

or under water. This poses a risk of fatal injury due to electric shock!

•  Do not expose the product to salt water (e.g. road salt during winter months), as this could

cause corrosion.

•  Mount the product to a horizontal surface only.
•  Do not mount the product to or inside vehicles.
•  When mounting the product, take into consideration the routing of the mains cable.
•  Only use a suitable, fixed mains cable for power supply.
•  A suitable switch is required for turning the product on and off.
•  The product must be secured via an existing sub-distribution unit with a 10/16A fuse. This

setup requires the installation of an upstream residual current circuit breaker (FI switch).

•  The product must be completely free of voltage for installation. Just turning off the light via the

switch does not make it entirely voltage-free.

•  Turn off the corresponding circuit breaker and/or automatic fuse to remove all voltage from

the power circuit. Secure them against unauthorized restart, e.g. by installing a warning sign.

Also switch off the relevant circuit breaker in order to disconnect all poles of the mains cable

from the mains supply.

•  Check the power circuit for any remaining voltage using an appropriate measuring device.

1.  Use a Phillips screwdriver to loosen the four short screws that connect the floor mount

bracket to the bottom of the product and then remove the floor mount bracket.

2.  Use the floor mount bracket as a template and mark the four drill hole positions through the

screw holes onto the mounting surface.

3.  Drill the four holes into the mounting surface and insert the dowels into the drill holes.

fig. 1

4.  Guide the mains cable through the hole from bottom up (fig. 1).
5.  Attach the floor mount bracket to the mounting surface using the four long screws.

The product is suitable for outdoor installation (protection type IP54) and is intended for lighting

entrance areas, patios, etc.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you

use the product for purposes other than those described above, the product may be damaged.

In addition, improper use can cause hazards such as short circuiting, fire, electric shock etc.

Read the instructions carefully and keep them. Make this product available to third parties only

together with its operating instructions.
This product complies with the statutory national and European requirements. All company

names and product names are trademarks of their respective owners. All rights reserved.

•  Outdoor floor lamp
•  Mounting material (4 x screw, 4 x dowel)
•  Operating instructions

The triangle containing a lightning symbol warns against danger of electric shock or

impairment of the electrical safety of the device.

An  exclamation  mark  in  a  triangle  indicates  important  notes  in  these  operating

instructions that must be strictly observed.

The “hand” symbol indicates special information and advice on operation.

The product is splash-proof (IP54).

Follow all instructions in the operating instructions.

•  The device is not a toy. Keep it out of the reach of children and pets. This poses a

risk of fatal injury due to electric shock!

•  Do  not  leave  packaging  material  lying  around  carelessly.  These  may  become

dangerous playing material for children.

•  Operate  the  product  only  via  a  common  household  power  supply  of

220 – 240 V/AC, 50 Hz.

•  The product is only suitable for fixed installation.
•  The product must not be installed in flood-prone areas. The same applies to areas

(e.g. depressions) in which rainwater could accumulate.

•  Never point a garden hose at the product.
•  The product may not be mounted in or under water.
•  Attention, LED light:

- Do not look directly into the LED light!
- Do not look into the beam directly or with optical instruments!

•  Protect  the  product  from  extreme  temperatures,  strong  jolts,  flammable  gases,

vapours and solvents.

•  Do not place the product under any mechanical stress.
•  If it is no longer possible to operate the product safely, take it out of operation and

protect it from any accidental use. Safe operation can no longer be guaranteed if

the product:

- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.