Eufab Professional 4-legged bicycle workstandBicycle accessories 16414 Professional bicycle workstand 16414 User Manual
Product codes
16414
entsprechenden Rohre legen und zuknöpfen. Der Lenkerhalter ist in der Länge verstellbar. Dazu bitte die Feststellschraube lösen, den Halter
auf die gewünschte Länge bringen und die Befestigungsschraube wieder festziehen.
Wenn die Position des bereits am Montageständer befestigten Fahrrades verändert werden soll, empfehlen wir, um Unfälle zu vermeiden, die
Hilfe einer zweiten Person.
auf die gewünschte Länge bringen und die Befestigungsschraube wieder festziehen.
Wenn die Position des bereits am Montageständer befestigten Fahrrades verändert werden soll, empfehlen wir, um Unfälle zu vermeiden, die
Hilfe einer zweiten Person.
AUFBEWAHRUNG UND PFLEGE
Für die Reinigung und Pflege Ihres neuen Montageständers empfehlen wir, diesen nur mit warmem Wasser und einem milden
Reinigungsmittel (pH-neutral) zu säubern. Benutzen Sie keine Scheuermittel, Lösemittel oder sonstigen Chemikalien. Wenn Sie den
Montageständer für längere Zeit nicht benötigen, bewahren Sie ihn bitte an einem trockenen, gut belüfteten Ort auf.
Reinigungsmittel (pH-neutral) zu säubern. Benutzen Sie keine Scheuermittel, Lösemittel oder sonstigen Chemikalien. Wenn Sie den
Montageständer für längere Zeit nicht benötigen, bewahren Sie ihn bitte an einem trockenen, gut belüfteten Ort auf.
GB
Art.-No.
Art.-No.
16414
BICYCLE REPAIR STAND
TECHNICAL SPECIFICATIONS
Maximum load: 30 kg
For bicycle frames size 25 mm - 40 mm
Read these instructions through carefully before using this product for the first time and afterwards retain them for future reference!
INTENDED USE
This bicycle assembly stand was developed for private use.
CONTENTS
1 x allen key
1 x tripod (A)
1 x telescopic pole (B)
1 x bicycle bracket (C)
1 x tripod (A)
1 x telescopic pole (B)
1 x bicycle bracket (C)
1 x tool tray (D)
1 x front wheel stabilizer (E)
1 x instructions
1 x front wheel stabilizer (E)
1 x instructions
ASSEMBLY
ATTACHING THE BICYCLE
Attention:
•
After inserting the bicycle verify it is securely positioned and the bicycle assembly stand is stable.
•
Please observe the maximum extension lengths of the telescopic rod (B)! Never extend the cross-bar on the bicycle bracket (C)
further than shown in fig.1.
further than shown in fig.1.
Select a section of the bicycle frame to be clamped into the bicycle assembly stand. This frame section must be at the bicycle’s centre of
gravity.
gravity.
Adjust the angle of the bicycle bracket (C) to fit the selected frame position of the bicycle (see examples in fig. 2 and fig. 3) and tighten the
screw (3) (fig.4). Now place the bicycle in the bicycle bracket and firmly secure frame. Firmly tighten the screw (4) (fig.4).
screw (3) (fig.4). Now place the bicycle in the bicycle bracket and firmly secure frame. Firmly tighten the screw (4) (fig.4).
•
We recommend performing the next step (height adjustment) with 2 persons.
You may then extend the telescopic rod (B) to the desired height.
Twisting the telescopic rod allows you to also change the position of the attached bicycle. Once you have reached the desired height and
position firmly tighten the screw (5) (fig. 3).
To secure the front wheel clamp the included front wheel stabilizer (E) between the front
handlebar and the telescopic pole (fig.4).
Twisting the telescopic rod allows you to also change the position of the attached bicycle. Once you have reached the desired height and
position firmly tighten the screw (5) (fig. 3).
To secure the front wheel clamp the included front wheel stabilizer (E) between the front
handlebar and the telescopic pole (fig.4).
TOOL TRAY
A magnet is located inside the large compartment of the tool tray for securing small parts.
Set up the tripod of the bicycle assembly stand by sliding the coupling (1)
on the tripod (A) all the way down.
Fold the feet (2) on the tripod legs down and ensure the product is placed
on a solid and even surface.
Now insert the telescopic pole (B) into the tripod, then mount the bicycle
bracket (C) onto the telescopic pole.
The tool tray (D) can be attached anywhere on tripod (A).
on the tripod (A) all the way down.
Fold the feet (2) on the tripod legs down and ensure the product is placed
on a solid and even surface.
Now insert the telescopic pole (B) into the tripod, then mount the bicycle
bracket (C) onto the telescopic pole.
The tool tray (D) can be attached anywhere on tripod (A).
Note
The feet on the assembly stand may optionally be screwed into the
surface to achieve greater stability. Be sure to use the suitable mounting
materials.
This product also includes a stabilizer for securing the front wheel of the
attached bicycle (E).
The feet on the assembly stand may optionally be screwed into the
surface to achieve greater stability. Be sure to use the suitable mounting
materials.
This product also includes a stabilizer for securing the front wheel of the
attached bicycle (E).