Bosch Appliances Home Security System DS924IPET Leaflet
© 2009 Bosch Security Systems, Inc.
130 Perinton Parkway, Fairport, New York, USA 14450-9199
(800) 289-0096
130 Perinton Parkway, Fairport, New York, USA 14450-9199
(800) 289-0096
06/09
DS924iPET Installation Instructions
P/N: F01U070392-04 Page 2
4.2
Attaching the Enclosure
• Attach the PIR base to the mounting plate and tighten the mounting plate
locking screw.
• Replace the cover, engaging the top first then securing the bottom latch.
• For added security, the cover may be locked to the base latch using the
• For added security, the cover may be locked to the base latch using the
small screw provided. The screw hole in the bottom of the cover must
be knocked out prior to replacing the cover.
be knocked out prior to replacing the cover.
5.0 Programming
General Guidelines
• Put the Control Panel in program mode.
• Trip the sensor’s tamper switch by removing its cover.
• Restore the tamper by replacing the sensor’s cover.
• Trip the sensor’s tamper switch by removing its cover.
• Restore the tamper by replacing the sensor’s cover.
Refer to the appropriate Control Panel installation manual for specific
instructions on programming this device.
instructions on programming this device.
6.0 Walk Testing
6.1 Setup
Loosen the vertical adjust screw and set the vertical adjustment to -4°.
Loosen the vertical adjust screw and set the vertical adjustment to -4°.
-4°
I
TEST
S
H
VERTICAL ADJUST
SCREW
0
4
8
4
8
0
4
8
4
8
Figure 5
6.2 Sensitivity Selection
• Locate the sensitivity pins. Move the shorting jumper to the appropriate
pair of pins.
• If the shorting jumper is not used or placed incorrectly, the sensor defaults
to Intermediate sensitivity.
Standard sensitivity is required for Pet Applications. This
setting is the most tolerant of environmental extremes.
setting is the most tolerant of environmental extremes.
Intermediate sensitivity should be used for any location where an
intruder is expected to cover only a small portion of the protected
area. This setting tolerates normal environments. Do not use this
setting for Pet Applications.
intruder is expected to cover only a small portion of the protected
area. This setting tolerates normal environments. Do not use this
setting for Pet Applications.
High sensitivity should only be used in quiet environments where
thermal and illumination transients are not anticipated. This setting
has the fastest response to intruder signals. Do not use this
setting for Pet Applications.
thermal and illumination transients are not anticipated. This setting
has the fastest response to intruder signals. Do not use this
setting for Pet Applications.
6.3
Pattern Testing
Pressing the Walk Test Switch will start a 90 second Walk Test Mode.
During this Test Mode, any activity in the sensor’s coverage pattern will
cause a transmitted alarm and LED activation. Each alarm will also extend
the Test Mode for an additional 90 seconds.
During this Test Mode, any activity in the sensor’s coverage pattern will
cause a transmitted alarm and LED activation. Each alarm will also extend
the Test Mode for an additional 90 seconds.
Walk Testing should be done across the coverage pattern. The edge of the
coverage pattern is determined by the first flash of the LED. This may
change slightly depending upon the sensitivity setting. Walk Test the unit
from both directions to determine the pattern boundaries.
coverage pattern is determined by the first flash of the LED. This may
change slightly depending upon the sensitivity setting. Walk Test the unit
from both directions to determine the pattern boundaries.
Note: Excessive use of the Walk Test Mode may reduce battery
life. Use only for initial setup and maintenance testing.
The detection pattern may be shifted ±10 degrees horizontally by rotating
the lens left or right to the appropriate marks on the lens frame.
the lens left or right to the appropriate marks on the lens frame.
6.4
Final Testing
Turn on all heating and air conditioning sources which would normally be
active during the protection period. Stand away from the sensor and outside
the coverage pattern and watch for alarms.
active during the protection period. Stand away from the sensor and outside
the coverage pattern and watch for alarms.
After setup and tests are completed, and there has been no activity in the
sensor’s coverage pattern for approximately 90 seconds, the LED will
flash to indicate that the Walk Test mode is ending.
sensor’s coverage pattern for approximately 90 seconds, the LED will
flash to indicate that the Walk Test mode is ending.
Note: When the Walk Test Mode has ended, an alarm can be
transmitted only after three (3) minutes have passed since
the previous alarm. This 3 minute lockout time reduces
unnecessary RF transmissions in high traffic areas thereby
extending battery life.
the previous alarm. This 3 minute lockout time reduces
unnecessary RF transmissions in high traffic areas thereby
extending battery life.
6.5
Maintenance
At least once a year, the range and coverage should be verified for proper
operation. To assure daily operation, the end user should be instructed to
walk through the far end of the coverage pattern to verify an alarm output
prior to arming the system.
operation. To assure daily operation, the end user should be instructed to
walk through the far end of the coverage pattern to verify an alarm output
prior to arming the system.
6.6
Battery Installation
The sensor is normally shipped with its battery installed. If battery
replacement is necessary observe proper polarity when installing a new
battery or the sensor may be damaged. When the battery is replaced, wait
at least 5 minutes after installing battery before activating the Walk Test
Mode.
replacement is necessary observe proper polarity when installing a new
battery or the sensor may be damaged. When the battery is replaced, wait
at least 5 minutes after installing battery before activating the Walk Test
Mode.
7.0 RF Testing
The actual RF transmitter range can be determined by performing a Dealer
Sensor Test as follows:
Sensor Test as follows:
• Remove the sensor’s cover and press the Walk Test Switch. Refer to
Figure 3 for the switch location.
• Replace the sensor’s cover.
• Using the appropriate touchpad for the Control Panel, enter the Dealer
• Using the appropriate touchpad for the Control Panel, enter the Dealer
Sensor Test Code.
• Move across the detection pattern until the sensor’s LED turns on. STOP
your motion.
• Note the number of siren beeps indicating how many RF packets the
control panel received from the sensor. You should hear 7-8 beeps. If
you hear 6 or fewer beeps, relocate the sensor and retest.
you hear 6 or fewer beeps, relocate the sensor and retest.
8.0 FCC Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference, including interference that
2. This device must accept any interference, including interference that
may cause undesired operation.
9.0 Coverage Patterns
DS924iPET Lens
A B C D E F G H I J K
P L
MQ
R N
O
T
V
S
U
A-K
L-O
P-S & V
T-U
0
0
0
35
11
3
10
Meters
Feet
0
6.5
6.5
0
A
B
C
D
E
F
G
H
I
J
K
M
L
N
P
O
R
V
U
T
S
Q
0
20
20
35
0
Feet
11
0
Meters
Figure 6
Changes or modifications not expressly approved by Interactive
Technologies, Inc. can void the user’s authority to operate the equipment.
Technologies, Inc. can void the user’s authority to operate the equipment.
®
Interactive Technologies, Inc.
2266 North Second Street
North Saint Paul, MN 55109
1-800-777-1415
2266 North Second Street
North Saint Paul, MN 55109
1-800-777-1415
S
I
H
S
I
H
S
I
H