Sharp MD-M3H User Manual
9
SETTING THE CLOCK
4,6,8
2
1
3,5,7,9
1
Press the ON/STAND-BY button to turn the
power on.
power on.
2
Press the CLOCK button.
DISC TOC
TRACK
MEMORY
RANDOM
TOTAL
REMAIN
TRACK
MEMORY
RANDOM
TOTAL
REMAIN
REC
kHz
MHz SLEEP
MHz SLEEP
3
Within 5 seconds, press the ENTER button.
DISC TOC
TRACK
MEMORY
RANDOM
TOTAL
REMAIN
TRACK
MEMORY
RANDOM
TOTAL
REMAIN
REC
kHz
MHz SLEEP
MHz SLEEP
4
Press the
or
button to select the time
display mode.
DISC TOC
TRACK
MEMORY
RANDOM
TOTAL
REMAIN
TRACK
MEMORY
RANDOM
TOTAL
REMAIN
"0:00"
→
The 24-hour display will appear.
→
(0:00 - 23:59)
"12:00 AM"
→
The 12-hour display will appear.
→
(AM or PM 12:00 - 11:59)
"0:00 AM"
→
The 12-hour display will appear.
→
(AM or PM 0:00 - 11:59)
●
Note that this can only be set when the unit is
first installed or it has been reset (see page 46).
first installed or it has been reset (see page 46).
5
Press the ENTER button.
DISC TOC
TRACK
MEMORY
RANDOM
TOTAL
REMAIN
TRACK
MEMORY
RANDOM
TOTAL
REMAIN
REC
kHz
MHz SLEEP
MHz SLEEP
6
Adjust the hour by pressing the
or
button.
DISC TOC
TRACK
MEMORY
RANDOM
TOTAL
REMAIN
TRACK
MEMORY
RANDOM
TOTAL
REMAIN
REC
kHz
MHz SLEEP
MHz SLEEP
●
When the
button is pressed once, the time will
increase by 1 hour. When the
button is pressed
once, the time will decrease by 1 hour.
●
When the 12-hour display selected, “
AM
” will
change to “
PM
” automatically.
7
Press the ENTER button.
DISC TOC
TRACK
MEMORY
RANDOM
TOTAL
REMAIN
TRACK
MEMORY
RANDOM
TOTAL
REMAIN
REC
kHz
MHz SLEEP
MHz SLEEP
8
Adjust the minutes by pressing the
or
button.
DISC TOC
TRACK
MEMORY
RANDOM
TOTAL
REMAIN
TRACK
MEMORY
RANDOM
TOTAL
REMAIN
REC
kHz
MHz SLEEP
MHz SLEEP
●
When the
button is pressed once , the time
will increase by 1 minute. When the
button is
pressed once, the time will decrease by 1 minute.
●
The hour setting will not advance even if min-
utes advance from "59" to "00".
utes advance from "59" to "00".
9
Press the ENTER button.
DISC TOC
TRACK
MEMORY
RANDOM
TOTAL
REMAIN
TRACK
MEMORY
RANDOM
TOTAL
REMAIN
REC
kHz
MHz SLEEP
MHz SLEEP
●
The clock starts operating from "0" seconds.
(Seconds are not displayed.)
(Seconds are not displayed.)
To see the time display:
Press the CLOCK button.
●
The time display will appear for about 5 seconds
even if stand-by mode.
even if stand-by mode.
Note:
●
The clock display will flash on and off at the push
of the CLOCK button when the AC power supply
is restored after a power failure occurs or after
the AC power lead is disconnected.
If this happens, follow the procedure below to
change the clock time.
of the CLOCK button when the AC power supply
is restored after a power failure occurs or after
the AC power lead is disconnected.
If this happens, follow the procedure below to
change the clock time.
To change the clock time:
1
Press the CLOCK button.
2
Within 5 seconds, press the ENTER button.
3
Perform steps 6 - 9 above.
To change the time display mode:
1
Reset the microcomputer (see page 48).
2
Perform steps 1 - 9 above.
In this example, the clock is set for the
24-hour (0:00) system.
24-hour (0:00) system.