Epson MovieMate 25 User Manual

exposed to rain or moisture, does not operate nor-

mally, or has been dropped.

• Do not expose this unit to water or place objects con-

taining liquids on this unit.

• Do not place the source of a naked flame, such as a lit

candle, on this unit.

• Connect this unit to an earthed electrical outlet.
• Ensure there is at least 8 inches between the exhaust

vent and any walls, etc.

• Ensure there is at least 4 inches between the air

intake vent and any walls, etc.

• Do not project when the lens cover is on.

It is possible that the lens cover may melt from the

heat and cause burns or injuries.

To interrupt the projection, press [Video On/Off] dur-

ing projection.

• Do not leave this unit or the remote control with its

batteries installed in such places as the inside of a car

with the windows closed, in direct sunlight, near the

intake/exhaust of an air conditioner or heater, or in

places where the temperature rises above normal.

This may have a negative effect upon the internal

parts of this unit and cause heat deformation or fire.

• When unplugging the power plug/power connector,

do not pull on the power cable.

Make sure you grasp the plug or connector part, then

unplug.

• Do not set the volume too high from the outset.

A loud sound may be produced suddenly that may

cause damage to the speaker or your hearing. As a

precaution, lower the volume before you switch off

this unit then raise it gradually after you switch it

back on.

• When using headphones, do not turn the volume up

too loudly.

You may adversely affect your hearing when listen-

ing at loud volumes over extended periods of time.

• When maintaining this unit, remove the power plug/

power connector form the wall outlet.

If not, you run the risk of an electric shock.

• Do not place the projector on an unstable cart, stand,

or table.

• Use the type of power source indicated on the projec-

tor. If you are not sure of the power available, consult

your dealer or local electricity company.

• Place the projector near a wall outlet where the plug

can be easily unplugged.

• Check the specifications of the power cable. Using

an inappropriate power cable could result in fire or

electric shock.

The power cable supplied with the projector is

intended to comply with power supply requirements

for the country of purchase.

If using the projector overseas, check the power sup-

ply voltage and outlet shape that conform to the local

standards, and purchase a proper power cable in the

country.

• Take the following precautions when handling the

plug. Failure to comply with these precautions could

result in fire or electric shock.
− Do not insert the plug into an outlet with dust

present.

− Insert the plug firmly into the outlet.
− Do not handle the plug with wet hands.

• Do not overload wall outlets, extension cables, or

integral convenience receptacles. This can cause fire

or electric shock.

• Do not place the projector where the cable can be

stepped on. It may result in fraying or damage to the

plug.

• Unplug the projector from the wall outlet before

cleaning. Use a damp cloth for cleaning. Do not use

liquid or aerosol cleaners.

• Do not block the slots and openings in the projector

case. They provide ventilation and prevent the pro-

jector from overheating. Do not place the projector

on a sofa, rug, or other soft surface, or in a closed-in

cabinet unless proper ventilation is provided.

• Never push objects of any kind through cabinet slots.

Never spill liquid of any kind into the projector.

• Unplug the projector from the wall outlet and refer

servicing to qualified service personnel under the fol-

lowing conditions:
− When the power cable or plug is damaged or

frayed.

− If liquid has been spilled into the projector, or it

has been exposed to rain, water, or excessive

humidity.

− If it does not operate normally when you follow the

operating instructions, or if it exhibits a distinct

change in performance, indicating a need for

service.

− If it has been dropped or the housing has been

damaged.

• The internal projector components consist of many

glass parts such as the lens and projection lamp.

The lamp is fragile, and can easily break. If the lamp

breaks, handle the projector with extreme care to

avoid injury from broken glass, and contact Epson

for a replacement.