Bissell 3545 User Manual
5
1.
3.
This User’s Guide has been designed to help you get the utmost satisfaction
from your BISSELL vacuum. You’ll find assembly and operating instructions,
safety precautions, as well as maintenance and troubleshooting instructions.
Please read this Guide thoroughly before assembling your vacuum.
from your BISSELL vacuum. You’ll find assembly and operating instructions,
safety precautions, as well as maintenance and troubleshooting instructions.
Please read this Guide thoroughly before assembling your vacuum.
Pay particular attention to the product diagram, assembly instructions, and
part names. Locate and organize all parts before assembly. Following this
User’s Guide will greatly enhance your ability to get the most performance
from your BISSELL vacuum for many years.
part names. Locate and organize all parts before assembly. Following this
User’s Guide will greatly enhance your ability to get the most performance
from your BISSELL vacuum for many years.
The only tool you’ll need to assemble your vacuum is a screwdriver.
Stand the vacuum upright and slide the base of the Handle firmly into the
grooves at the top of the vacuum body.
grooves at the top of the vacuum body.
Check to be sure the Handle is fitted to the vacuum body. If there is a gap in
front, continue to push firmly until the Handle is flush.
front, continue to push firmly until the Handle is flush.
Insert one screw from the assembly packet into the existing hole in the back of
the Handle. Tighten securely with a screwdriver.
the Handle. Tighten securely with a screwdriver.
Position the hose collar on the back of the vacuum as shown.
Attach the hose collar with two screws from the assembly packet. Tighten
securely with a screwdriver.
securely with a screwdriver.
Line up the tabs on the base of the Twist ‘n Snap Hose with the
corresponding tab notches on the hose collar as shown. Turn the Twist ‘n
Snap Hose to the left to lock the hose into place.
corresponding tab notches on the hose collar as shown. Turn the Twist ‘n
Snap Hose to the left to lock the hose into place.
Grasping the Quick Reach
®
Handle, slide the end of the Hose Wand onto
the Suction Intake Opening. Snap the Hose into the Hose Clip.
NOTE: The Powerfoot will not operate effectively unless the
Hose Wand is firmly attached to the Suction Intake Opening.
Hose Wand is firmly attached to the Suction Intake Opening.
Place the Crevice Tool inside the Extension Wand and slide them into the
Storage Clip as shown.
Storage Clip as shown.
Snap the Combination Upholstery/Dusting Brush Tool into the Storage Clip
as shown.
as shown.
Attach the TurboBrush by aligning the small holes near the brush roll with
the tabs at the bottom of TurboBrush housing. Snap TurboBrush into place
as shown.
the tabs at the bottom of TurboBrush housing. Snap TurboBrush into place
as shown.
Press the Handle Release Pedal with your foot to place your vacuum into one of
three cleaning positions.
three cleaning positions.
Upright- For storage and above floor cleaning with special tools.
Normal Cleaning- Press Handle Release Pedal once. Use for most
household floor cleaning tasks.
Low Cleaning- With the vacuum in normal cleaning position press Handle
Release Pedal again. Use for reaching under low furniture
such as tables, chairs and beds.
How To Use This Guide
WARNING:
Plastic film can be dangerous.
To avoid danger of suffocation,
keep away from babies
and children.
To avoid danger of suffocation,
keep away from babies
and children.
1.
2.
3.
1.
2.
3.
4.
Handle Position
How To Use Your BISSELL Vacuum
1.
2.
3.
How To Assemble
Attach Handle to Vacuum
Attach Vacuum Hose and Tools
Tip:
Before cleaning under
low furniture, check
area first for objects
that might harm the
unit or block the
Vacuum Hose.
low furniture, check
area first for objects
that might harm the
unit or block the
Vacuum Hose.
5.
6.
7.
5.
6.
4.
1.
2.
Hose
Collar
Collar
3.
Select Models Only