Woodstock SHOP FOX D2267 Leaflet
Dust Collection Nozzle
D2267
Assembly:
1. Thread the (3) M8-1.25 x 25 Feet into the bottoms
1. Thread the (3) M8-1.25 x 25 Feet into the bottoms
of the (3) Legs.
2. Using the (12) M6-1 x 8 Phillips Head Screws,
6mm Lock Washers, and 6mm Flat Washers, attach
the (3) Legs to the Main Tube Body. Be sure the
Lock Washers are between the Flat Washers and the
Phillips Screw heads when tightened down.
the (3) Legs to the Main Tube Body. Be sure the
Lock Washers are between the Flat Washers and the
Phillips Screw heads when tightened down.
3. Thread the M8-1.25 x 20 Lock Knob into the
threaded hole on the side of the Main Tube Body.
4. Attach the Fixed Support to the top end of the
Silver Main Tube Body using (2) M6-1.0 x 20
Phillips Head Screws.
Phillips Head Screws.
5. Thread the M10-1.5 Hex Nut onto the end of the
M10-1.5 x 15 Lock Knob. Place the end of the
Lock Knob and Hex Bolt assembly through the slot
on the Vacuum Tube. After the knob has been slide
through the slot, place the 10mm Flat Washer on
the threaded end of the Knob.
Lock Knob and Hex Bolt assembly through the slot
on the Vacuum Tube. After the knob has been slide
through the slot, place the 10mm Flat Washer on
the threaded end of the Knob.
6. Carefully thread the Knob into the threaded hole in
the Fixed Support. Be sure the Flat Washer is
between the Fixed Support and the Vacuum Tube.
This Washer acts as a pivot point when adjusting
the Nozzle position. Tighten the Knob until the
Vacuum Tube remains stationary.
between the Fixed Support and the Vacuum Tube.
This Washer acts as a pivot point when adjusting
the Nozzle position. Tighten the Knob until the
Vacuum Tube remains stationary.
7. Slide the Nozzle into the end of the Vacuum Tube.
The Nozzle can be rotated 360° within the Vacuum
Tube. Thread the M6-1 x 15 Lock Knob into the
threaded hole on the top of the Vacuum Tube. This
Knob locks the Nozzle into position.
Tube. Thread the M6-1 x 15 Lock Knob into the
threaded hole on the top of the Vacuum Tube. This
Knob locks the Nozzle into position.
8. You are now ready to enjoy dust collection in just
about any location of your shop. If the Stand is
unlevel, thread the Feet in and out until proper
adjustment is achieved.
unlevel, thread the Feet in and out until proper
adjustment is achieved.
If You Need Assistance:
We hope you will find that your Shop Fox
We hope you will find that your Shop Fox
®
Model
D2267 is easily assembled and put to use. Should you
have any questions about this product, please contact
the dealer where you purchased it, or you can contact
the Woodstock International Technical Department at
1-360-734-3482, Monday through Friday, between the
hours of 7:00 am to 5:00 pm PST or e-mail us at:
tech-support@woodstockint.com
have any questions about this product, please contact
the dealer where you purchased it, or you can contact
the Woodstock International Technical Department at
1-360-734-3482, Monday through Friday, between the
hours of 7:00 am to 5:00 pm PST or e-mail us at:
tech-support@woodstockint.com
Wear safety glasses during
the entire assembly
process. Failure to comply
may result in serious
personal injury.
the entire assembly
process. Failure to comply
may result in serious
personal injury.
Be sure to read the entire instruction sheet
before beginning the construction of this prod-
uct. Follow every step and use the recommended
tools and supplies. Also, read the instruction
manuals for any tools you are using to complete
this project. Be certain that the tools used for
this installation are intended for the task which
will be performed. Failure to do this could result
in serious personal injury.
before beginning the construction of this prod-
uct. Follow every step and use the recommended
tools and supplies. Also, read the instruction
manuals for any tools you are using to complete
this project. Be certain that the tools used for
this installation are intended for the task which
will be performed. Failure to do this could result
in serious personal injury.
The Shop Fox
®
D2267 is designed to position the suc-
tion of your dust collector near machines that are not
equipped with dust ports and near other sources of
wood chips. The nozzle is attached to a fully adjustable
stand that permits an endless combination of nozzle
positions.
equipped with dust ports and near other sources of
wood chips. The nozzle is attached to a fully adjustable
stand that permits an endless combination of nozzle
positions.
Tools Needed:
Phillips Screwdriver
Phillips Screwdriver
NOTICE
The performance of your Model D2267 will
only be as good as the performance of your
dust collector. Regular maintenance of
your dust collector will ensure maximum
performance from your Model D2267, with-
in the limitations of your dust collector.
only be as good as the performance of your
dust collector. Regular maintenance of
your dust collector will ensure maximum
performance from your Model D2267, with-
in the limitations of your dust collector.