La Crosse Technology 914-604 Leaflet

Page of 2
 
 
Model 914-604 
Infra-red thermometer 
 
 
 
 
Congratulations on your purchase of the Infrared 
Thermometer! One-click for a temperature reading.  
 
No surface contact required, prevents contamination. 
 
Take a Measurement:  
Place the thermometer close to the item to measure.  
Click the button once to measure the surface temperature. The 
reading will display for 15 seconds. 
 
Hold the button for ongoing readings. 
 
Auto Shut Off: 
When the button has not been pressed for 15 seconds, the 
thermometer will automatically shut off to save power. 
 
Note: When measuring temperatures above 199.9 °F the last 
number will be smaller, due to LCD size. Example: 205 °F will 
show as 20
5
 
Applications: 
 
Check doors and windows for drafts. 
 
Maintain proper cooking, cooling and holding 
temperatures. 
 
Measure food or liquid temperature (no contact, thus no 
contamination) 
 
Measure oven, stove & grill temperatures up to 390.2 °F. 
 
Check heating & cooling ducts, in-floor heating and 
furnace temperatures. 
 
Measure engine exhaust, tires and hard to reach areas 
 
Description of measuring principle 
When making a temperature measurement, the surface 
radiation of the object measured is evaluated, using the 
principle of radiation thermometry.  This is a purely passive 
process, i.e. no radiation is transmitted, but instead, use made 
of the natural electromagnetic radiation energy (heat radiation). 
Everything above a temperature of 
absolute zero (−459.67 °F) 
has heat radiation.  
 
D/S Ratio: The distance to target diameter ratio (Distance: 
Spot) is 1:1 therefore the device should be positioned as close 
to the target as possible. As you move farther from the target, 
you will receive ambient temperature around the target. 
Measuring Tips: 
 
Not recommended for use in measuring shiny or polished 
metal surfaces (stainless steel, aluminum, etc.) The 
reading will not be accurate. 
 
It is not possible to take measurements through 
transparent materials (glass, Plexiglas, etc.). It will 
measure the temperature of the transparent surface 
instead. 
 
It is not possible to measure air temperatures. 
 
Measurement errors can occur due to air contaminated 
with dust, steam, smoke, etc. 
 
Battery Replacement: 
 
Battery is low and no more measurements are possible. 
Replace the battery immediately with a CR2032 lithium button 
cell.  
 
1- Power off the thermometer before replacing the battery 
 
A malfunction may occur if the power is on during battery 
replacement. If a malfunction occurs, restart the device.  
2-Twist the battery cover on the back of thermometer to loosen 
the cover and remove the old battery. A coin will work well. 
3- The new CR2032 battery is installed positive side up.  
 
Take care that the metal contacts at the top of the battery 
compartment are not bent.  
 
4-Replace the battery cover and tighten. 
 
Troubleshooting: 
 
Problem 
Solution 
 
 
 
 
 
No Display: 
Press the button 
 
 
Ensure battery polarity is correct 
 
 
Change the battery 
 
 
 
 
Display “oFF”: 
Automatic switch off (15 seconds)   
 
 
Display “Hi”: 
Temperature is above 390.2 °F 
 
 
 
Display “Lo”: 
Temperature below -27.4 °F 
 
 
 
Caution! 
 
Do not aim too close at hot or dangerous targets. 
 
Keep the thermometer and battery away from children. 
 
Batteries can explode if thrown into fire, short-circuited, 
taken apart or recharged. 
 
Battery can be fatal if swallowed. If a battery has been 
swallowed, get medical attention immediately. 
 
Batteries contain harmful acids. Change low batteries as 
soon as possible to prevent damage caused by a leaking 
battery. 
 
Wear chemical resistant protective gloves and safety 
glasses when changing the battery. 
 
Care and Maintenance: 
 
Do not place the instrument near extreme temperature, 
vibration or shock. 
 
Protect the unit from large abrupt temperature changes. 
 
Do not store near objects of high temperature. 
 
Do not immerse the unit in water. Water can penetrate and 
cause malfunction. Protect from moisture. 
 
Steam, dust, some can prevent accurate measurement by 
obstructing the units optics. 
Metal Contacts 
Metal Contacts