Pelco Computer Keyboard C581M-B User Manual
Pelco Manual C581M-B (1/04)
35
PROGRAMMING A PRESET
1.
Press the MAIN or SPOT MONITOR key. The green LED over the MAIN or SPOT key
lights. When using the MAIN MONITOR, the SPOT MONITOR DISPLAY menu item in
the Advanced System Setup menu must be set to TRACK MAIN (refer to the
lights. When using the MAIN MONITOR, the SPOT MONITOR DISPLAY menu item in
the Advanced System Setup menu must be set to TRACK MAIN (refer to the
Advanced System Setup
section).
2.
Select the camera.
Addressing by Multiplexer (Switch 7 OFF)
a.
a.
On the number pad, press the address number of the multiplexer (1-16 if the
keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a
server), then press the UNIT key. The LED displays the address.
keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a
server), then press the UNIT key. The LED displays the address.
b.
On the number keypad press the number of the camera (1-16), then press the
CAM key.
CAM key.
Addressing Consecutively (Switch 7 ON)
On the number keypad press the number of the camera, then press the CAM
key. Refer to Table C for camera numbers.
On the number keypad press the number of the camera, then press the CAM
key. Refer to Table C for camera numbers.
3.
Position the camera using the pan/tilt and lens keys.
4.
On the number keypad press the number of the preset, then hold down the
PRESET key for five seconds.
PRESET key for five seconds.
PROGRAMMING A PATTERN
1.
Press the MAIN or SPOT MONITOR key. The green LED over the MAIN or SPOT key
lights. When using the MAIN MONITOR, the SPOT MONITOR DISPLAY menu item in
the Advanced System Setup menu must be set to TRACK MAIN (refer to the
lights. When using the MAIN MONITOR, the SPOT MONITOR DISPLAY menu item in
the Advanced System Setup menu must be set to TRACK MAIN (refer to the
Advanced System Setup
section).
2.
Select the camera.
Addressing by Multiplexer (Switch 7 OFF)
a.
a.
On the number pad, press the address number of the multiplexer (1-16 if the
keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a
server), then press the UNIT key. The LED displays the address.
keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a
server), then press the UNIT key. The LED displays the address.
b.
On the number keypad press the number of the camera (1-16), then press the
CAM key.
CAM key.
Addressing Consecutively (Switch 7 ON)
On the number keypad press the number of the camera, then press the CAM key.
Refer to Table C for camera numbers.
On the number keypad press the number of the camera, then press the CAM key.
Refer to Table C for camera numbers.
3.
On the number pad, press a number key for the pattern number. Example: If you are
programming pattern 1 press the number 1 key. Then hold down the PATTERN key
until the message PROGRAMMING PATTERN appears on the screen.
programming pattern 1 press the number 1 key. Then hold down the PATTERN key
until the message PROGRAMMING PATTERN appears on the screen.
4.
Move the camera through the pattern using the pan/tilt and lens keys.
5.
To stop programming the pattern, repress the number key for the pattern followed by
the PATTERN key. Example: Press number 1 and then the PATTERN key if you are
programming pattern 1. The message PROGRAMMING PATTERN disappears.
the PATTERN key. Example: Press number 1 and then the PATTERN key if you are
programming pattern 1. The message PROGRAMMING PATTERN disappears.
NOTE:
The LEDs above
the camera buttons on the
multiplexer will illuminate to
indicate which cameras are
being displayed.
multiplexer will illuminate to
indicate which cameras are
being displayed.
NOTE:
Refer to your dome
or pan and tilt system
manual for information on
the number of available
patterns and pattern
durations.
manual for information on
the number of available
patterns and pattern
durations.