DKS Enterprises PC Compatible Multi-Door Access Controller 1838 User Manual
3.6 FOUR-DIGIT ENTRY CODE
A DoorKing slave keypad (P/N 1814-075) is required if four-digit entry codes are going to be used to
access a door or gate. It is important to understand that four-digit entry codes are not the same as a
five-digit PIN (Personal Identification Number) code inputted to the system from a weigand keypad.
Four-digit entry codes can only activate relay 1 or relay 2 on the 1842-010 circuit board, regardless if
Tracker expansion boards are used or not. If Tracker expansion boards are controlled by relay 2, the
four-digit entry codes must be set to activate relay 1. If both relays are used to control Tracker
expansion boards, then four-digit entry codes cannot be used and should not be programmed into the
system. Under this condition, if digital PIN codes are desired, use a weigand keypad (P/N 1815-050
or 1815-051) connected to a Tracker board.
access a door or gate. It is important to understand that four-digit entry codes are not the same as a
five-digit PIN (Personal Identification Number) code inputted to the system from a weigand keypad.
Four-digit entry codes can only activate relay 1 or relay 2 on the 1842-010 circuit board, regardless if
Tracker expansion boards are used or not. If Tracker expansion boards are controlled by relay 2, the
four-digit entry codes must be set to activate relay 1. If both relays are used to control Tracker
expansion boards, then four-digit entry codes cannot be used and should not be programmed into the
system. Under this condition, if digital PIN codes are desired, use a weigand keypad (P/N 1815-050
or 1815-051) connected to a Tracker board.
3.6.1
Programming Four-digit Entry Codes
1. Press
* 0 2 and enter the four-digit MASTER CODE _ _ _ _ (beep).
2.
Enter the directory code (1, 2, 3 or 4 digits depending on what was programmed in
3.4.1) then press * (beep).
3.4.1) then press * (beep).
3.
Enter the four-digit entry code _ _ _ _ then press * (beep).
4.
Repeat steps 2 and 3 to enter additional entry codes.
5. Press
0 # TOGETHER to end this programming step (beeeeeep).
3.6.2
Delete Four-digit Entry Codes
1. Press
* 0 2 and enter the four-digit MASTER CODE _ _ _ _ (beep).
2.
Enter the directory code (1, 2, 3 or 4 digits depending on what was programmed in
3.4.1) then press * (beep).
3.4.1) then press * (beep).
3. Press
# # # # * (beep).
4.
Repeat steps 2 and 3 to delete more entry codes.
5. Press
0 # TOGETHER to end this programming step (beeeeeep).
3.6.3 Entry
Code
Ranges
Four-digit entry codes can be made to activate relay 1 or relay 2 or any combination of relays by
programming HI and LOW ranges for each relay. Ranges may overlap, which will cause more than
one relay to activate if this is desired. For example, if the low boundary for relay 1 and 2 is 2000, and
the hi boundary is 3000 for relay 1 and 4000 for relay 2, then entry codes between 2000 and 3000 will
activate both relays, and entry codes between 3001 and 4000 will only activate relay 2.
programming HI and LOW ranges for each relay. Ranges may overlap, which will cause more than
one relay to activate if this is desired. For example, if the low boundary for relay 1 and 2 is 2000, and
the hi boundary is 3000 for relay 1 and 4000 for relay 2, then entry codes between 2000 and 3000 will
activate both relays, and entry codes between 3001 and 4000 will only activate relay 2.
1. Press
* 1 2 and enter the four-digit MASTER CODE _ _ _ _ (beep).
2. Press
1 * to set relay 1, or 2 * to set relay 2 boundaries.
3.
Enter the four-digit low boundary _ _ _ _ then press * (beep).
4.
Enter the four-digit high boundary _ _ _ _ then press * (beep).
5.
Repeat steps 2, 3, and 4 to set the other relay boundaries (or proceed to step 7).
6. Press
0 # TOGETHER to end this programming step (beeeeeep).
Page
34
1838-065-L-3-10