Q-Logic Keyless Entry Alarm Upgrade Module APS-30 User Manual
KEYLESS ENTRY ALARM UPGRADE MODULE
INSTALLATION INSTRUCTIONS
PRE - INSTALLATION NOTES :
STAND ALONE PASSIVE ALARM
When installing the APS-30 as a stand alone passive alarm system, the dip switches must be set as follows;
Dip Switch # 1 = ON
Dip Switch # 2 = ON
Dip Switch # 3 = OFF
Dip Switch # 4 = OFF
Dip Switch # 5 = OFF
Dip Switch # 6 = OFF
Dip Switch # 2 = ON
Dip Switch # 3 = OFF
Dip Switch # 4 = OFF
Dip Switch # 5 = OFF
Dip Switch # 6 = OFF
PASSIVE / ACTIVE ARMING SELECTION : DIP SWITCH # 1
This alarm can be programmed to operate as either a " PASSIVE " or " ACTIVE " arming security system.
As a passive arming system, the alarm will automatically arm 30 seconds after the ignition key is turned off, one door is opened, then
all doors are closed. Additionally, if a door has been left opened, or if one of the trigger zones is defective, the system will always arm
10 minutes after the ignition key has been turned off, and ignore the defective trigger zone.
all doors are closed. Additionally, if a door has been left opened, or if one of the trigger zones is defective, the system will always arm
10 minutes after the ignition key has been turned off, and ignore the defective trigger zone.
As an active arming system, the alarm will arm only when the vehicle’s doors have been locked using the existing OEM Keyless Entry
Transmitter.
Transmitter.
The system is shipped from the factory in the active arming mode, and to select the passive arming mode, move dip switch # 1 to the "
ON " position.
ON " position.
1 OR 2 WIRE DISARM INPUT SELECTION : DIP SWITCH # 2
This alarm can be programmed for either 1 wire or 2 wire disarm operation.
Many OEM keyless entry systems use on - board door unlock relays, which usually results in the ability to disarm the aftermarket security
upgrademodulebyunlockingthedoorsusingthedoorpanelunlockswitch.Wiringthesystemfor2wiredisarmwilleliminatethisproblem.
The system is shipped from the factory in the 2 wire disarm mode, and to select the 1 wire disarm mode, move dip switch # 2 to the "
ON " position.
upgrademodulebyunlockingthedoorsusingthedoorpanelunlockswitch.Wiringthesystemfor2wiredisarmwilleliminatethisproblem.
The system is shipped from the factory in the 2 wire disarm mode, and to select the 1 wire disarm mode, move dip switch # 2 to the "
ON " position.
HORN OR SIREN OUTPUT SELECTION : DIP SWITCH # 3
This system provides an output that should be used to drive the siren, but can be programmed to pulse the vehicle's horn.
When utilizing the horn, an additional relay is required. Caution: on many vehicles the factory horn is not designed
forcontinuoususe,anditisrecommendedthatthesirenisusedforthesevehicles.Checktoseeifthehorninthevehicle
is the same part that is used in a vehicle with the factory installed security system.
When utilizing the horn, an additional relay is required. Caution: on many vehicles the factory horn is not designed
forcontinuoususe,anditisrecommendedthatthesirenisusedforthesevehicles.Checktoseeifthehorninthevehicle
is the same part that is used in a vehicle with the factory installed security system.
DIP SWITCH SETTINGS
1
2
3
4
5
6
2
3
4
5
6
PASSIVE ARMING
1 WIRE DISARM
HORN MODE
INSTANT TRIGGER
- ARM INPUT
VOLTAGE SENSE
ON
OFF
ACTIVE ARMING
2 WIRE DISARM
SIREN MODE
ENTRY DELAY
+ ARM INPUT
HARDWIRE
Model APS-30