Guardian Technologies K1148-X 4/98 Leaflet
Cable:
The RS-232 interface is attached to a RJ-45 to
DB-9 connector with either a 4 conductor or 8
conductor “phone” cable. The cable is NOT pin
compatible with standard 4 conductor phone cords.
See Figure 2: Connection Cable. For a
4 conductor cable only pins 3,4,5,6 on the RJ-45
connector will be used. As of software revision
8.04 only pins 3,4,5,6 are supported eliminating
the necessity for 8 conductor connections.
The RS-232 interface is attached to a RJ-45 to
DB-9 connector with either a 4 conductor or 8
conductor “phone” cable. The cable is NOT pin
compatible with standard 4 conductor phone cords.
See Figure 2: Connection Cable. For a
4 conductor cable only pins 3,4,5,6 on the RJ-45
connector will be used. As of software revision
8.04 only pins 3,4,5,6 are supported eliminating
the necessity for 8 conductor connections.
DTE vs. DCE:
The RS-232 interface can operate in either Date Terminal Equipment (DTE) or Data Communication Equipment
(DCE) mode. A jumper (J3) is located to the right of the RJ-45 on the interface board. Attach the supplied
jumper across the center and bottom pin for DCE operation or the top two pins for DTE. Most applications
will require DCE including connection to a PC and a printer.
The RS-232 interface can operate in either Date Terminal Equipment (DTE) or Data Communication Equipment
(DCE) mode. A jumper (J3) is located to the right of the RJ-45 on the interface board. Attach the supplied
jumper across the center and bottom pin for DCE operation or the top two pins for DTE. Most applications
will require DCE including connection to a PC and a printer.
Protocol:
The 2-way RS-232 standard for the Destiny control
panel is an open standard and is available by calling
Technical Support at 800-272-7937.
The 2-way RS-232 standard for the Destiny control
panel is an open standard and is available by calling
Technical Support at 800-272-7937.
Printer Reports:
When enabled (as described in Programming, above), any event programmed to appear in the Event
Memory Log will be printed when an event occurs. All items in the system that can be sent to a central
station will be printed as the event occurs. The “Report to Central Station” programming option does
not affect the printer report.
Note: the RS-232 does not buffer events, if a printer is off-line the event will not be printed.
When enabled (as described in Programming, above), any event programmed to appear in the Event
Memory Log will be printed when an event occurs. All items in the system that can be sent to a central
station will be printed as the event occurs. The “Report to Central Station” programming option does
not affect the printer report.
Note: the RS-232 does not buffer events, if a printer is off-line the event will not be printed.
4 Conductor Cable: Top View
8 Conductor Cable: Top View
Figure 2: Connection Cable
Br Bl Y G R B k O G y
Br Bl Y G R B k O G y
Y G R B k
Y G R B k
Programming:
The following programming options are provided:
The following programming options are provided:
001 - Enable the RS-232 adapter
002 - Enable printer compatibility
004 - Use English Line text (for printers only)
008 - Enable 2-Way RS-232 communication (for PC connections)
064 - Enable Remote System Mode
002 - Enable printer compatibility
004 - Use English Line text (for printers only)
008 - Enable 2-Way RS-232 communication (for PC connections)
064 - Enable Remote System Mode
Place the system into program mode (default: 9,1,7,3), enter location 0,1,5,5 and then enter the sum of
options to be enabled. For example, to enable 2-way communication, enter 0,0,9 (001 + 008). For
printing, enter 0,0,7 (001 + 002 + 004).
options to be enabled. For example, to enable 2-way communication, enter 0,0,9 (001 + 008). For
printing, enter 0,0,7 (001 + 002 + 004).
Format:
The following is an example of the printer output when connected to the RS-232 port.
Event
The following is an example of the printer output when connected to the RS-232 port.
Event
User
Time
Month
Day
Open - System Disarmed
User = 01
13:23
July
29