BBQ Pro Smoker 137.23672310 User Manual

‡ BEFORE ASSEMBLY READ ALL INSTRUCTIONS CAREFULLY.
‡ ASSEMBLE UNIT ON A CLEAN

,

FLAT SURFACE.

‡ TOOLS NEEDED: ADJUSTABLE WRENCH, PHILLIPS HEAD SCREWDRIVER

Do not tighten screws all the way. Leg
frames may need to be adjusted during
assembly.

Attach rear legs (4), right front leg (25)
and left front leg (26) to bottom of smoker
body (1) using M6*12(A).

Do not fully tighten screws

Attach control panel (5) to right front
leg (25) as shown usingM6*12(A).

Repeat on opposite side attaching

control panel (5) to left front leg (26).

Position burner box (6) over center
hole

in

bottom

of

smoker

body,

carefully aligning venturi over valve
orifice as shown. Attach burner box to
smoker bod y using M6*12 (A).

Firmly attach ignition wire to piezo
ignitor on control panel as shown in

!

!

Ɣ

Ɣ

Ɣ

Ɣ

Ɣ

Ɣ

Ɣ

Ɣ

Ɣ

Ɣ

Inspect hose before each use. If there are signs of 

wear, cuts, or leaks, replace unit. DO NOT USE.

Inspect burner before each use. Check burner and 

burner ventura tube for insects and insect nests. A 

clogged tube can lead to a fi re beneath appliance.

Perform Soapy Water Test.

To use turn gas cylinder ON, turn regulator control 

valve ON, turn burner control knob clockwise and 

push ignitor button to light.

If ignition does not take place within five seconds, 

turn gas control valve to off position and wait fi ve 

minutes and repeat lighting procedures. If ignition still 

1. Read all instructions and warnings before lighting.

2. Check gas control valve and gas cylinder valve to be 

certain it is in OFF position before connecting to gas 

cylinder. Perform soapy water test before each use.

3. Open door during lighting.

4. Turn gas control valve on, turn gas cylinder valve on.

5. Place a long, lit fi replace match stick close enough to 

burner to ignite.

6. After each use, fi rst 
turn gas control valve off, 
then gas cylinder valve 
off. Always allow unit to 
cool completely before 
touching, moving or 
storing.

Connect hose regulator to LP Gas Cylinder

Make sure gas cylinder valve is closed. Turn 

knob clockwise until it stops.

Make sure control knob on smoker is in the 

“OFF” position.

1.

2.

3.

4.

does not occur, see match light directions below.

After use turn burner control knob OFF, turn regulator 

control valve OFF, then turn gas cylinder OFF.

Burner control knob adjusts burner flame. Turn control 

knob clockwise SLOWLY to increase fl ame. Turn 

control knob counter-clockwise to decrease flame and 

shut flame off.

Visually check burner fl ame. A CORRECT FLAME 

should be blue with a small amount of yellow at the tip. 

An INCORRECT FLAME is excessively yellow and 

irregular. If an incorrect flame occurs, turn burner 

The hose hook must 

be fasten at the right 

front leg at anytime 

and check before 

ignition. (Please see 

ASSEMBLY

INSTRUCTION STEP 

14)

Remove protective cap from 

gas cylinder and coupling 

nut if applicable.

Center and insert regulator 

nipple into valve outlet on 

gas cylinder as shown in fi 

gure on the left. Turn 

regulator coupling nut 

clockwise until it stops. DO 

NOT OVER TIGHTEN.

control knob to “OFF 

position,

turn off regulator and 

propane tank. Allow unit 

to cool and then clean 

burner.

Let burner completely 

dry before re-lighting.