Boss Audio Systems GT-10B User Manual
122
Chapter 8 Parameters Guide
These settings are applied to the overall sound.
SW&PDL FUNCTION
MASTER
MASTER
Parameter/
Range
Range
Explanation
Patch Level
0–200
Adjusts the volume of the patch.
Master Low (Master Low EQ Gain)
-12–+12dB
Adjusts the low frequency range tone.
Master Mid f (Master Middle EQ Frequency)
20.0Hz–10.0kHz
Specify the center of the frequency range that
will be adjusted by the “Master Mid G.”
will be adjusted by the “Master Mid G.”
Master Mid Q (Master Middle EQ Q)
0.5–16
Adjusts the width of the area affected by the EQ
centered at the Master Mid f.
Higher values will narrow the area.
centered at the Master Mid f.
Higher values will narrow the area.
Master Mid G (Master Middle EQ Gain)
-12–+12dB
Adjusts the middle frequency range tone.
Master High (Master High EQ Gain)
-12–+12dB
Adjusts the high frequency range tone.
MASTER BPM/KEY
Parameter/
Range
Range
Explanation
Master BPM
40–250
Adjust the BPM value for each patch.
BPM (beats per minute) indicates the number of quarter note beats that
occur each minute.
occur each minute.
When you have an external MIDI device connected, the Master BPM
synchronizes to the external MIDI device’s tempo, making it impossible to
set the Master BPM. To enable setting of the Master BPM, set “Sync Clock”
(p. 139) to Internal.
synchronizes to the external MIDI device’s tempo, making it impossible to
set the Master BPM. To enable setting of the Master BPM, set “Sync Clock”
(p. 139) to Internal.
Master Key
C (Am)–B
(G#m)
(G#m)
This sets the key for the HARMONIST.
The key setting corresponds to the key of the song (#,
b
) as follows.
PEDAL FX
Parameter/
Range
Range
Explanation
CTL1 Func (CTL1 Pedal Function)/
CTL2 Func (CTL2 Pedal Function)/
EXPSwFunc (EXP Pedal Switch Function)
CTL2 Func (CTL2 Pedal Function)/
EXPSwFunc (EXP Pedal Switch Function)
Off
The function is not assign to the pedals.
Ch. A/B
Switches between effect channel A and B.
Comp
Switches the COMP on and off.
OD/DS
Switches the OD/DS on and off.
Preamp
Switches the PREAMP/SPEAKER on and off.
EQ
Switches the EQ on and off.
FX-1
Switches the FX-1 on and off.
FX-2
Switches the FX-2 on and off.
Delay
Switches the DELAY on and off.
Chorus
Switches the CHORUS on and off.
Reverb
Switches the REVERB on and off.
Pedal FX
Switches the PEDAL FX on and off.
Send/Return
Switches the SEND/RETURN on and off.
Amp Ctl
Switches the Amp Control on and off.
Tuner
Switches the TUNER on and off.
Manual
Switches the MANUAL MODE on and off.
PL
Switches the PHRASE LOOP on and off.
PL Rec/Play
Records/plays back the phrase.
PL Clear
Clears the phrase.
PL Mute/Ply
Mutes playback of the phrase.
BPM Tap
Used for tap input of the Master BPM.
Delay Tap
Used for tap input of the delay time.
MIDI Start
Controls the Start/Stop of external MIDI devic-
es (such as sequencers).
es (such as sequencers).
MMC Play
Controls the Play/Stop of external MIDI devic-
es (such as hard disk recorders).
es (such as hard disk recorders).
Lev +10
Increases the patch volume level by 10 units.
Lev +20
Increases the patch volume level by 20 units.
Lev -10
Decreases the patch volume level by 10 units.
Lev -20
Decreases the patch volume level by 20 units.
Num Inc
Switches to the next higher patch number in the
same bank as the currently selected patch.
same bank as the currently selected patch.
Num Dec
Switches to the next lower patch number in the
same bank as the currently selected patch.
same bank as the currently selected patch.
Bank Inc
Switches to the next higher bank number.
Bank Dec
Switches to the next lower bank number.
LED Moment *1
The pedal indicator lights up while you press
the pedal, and it goes out when you release the
pedal.
the pedal, and it goes out when you release the
pedal.
LED Toggle *1
The pedal indicator lights up and goes out
when alternate each time you press the pedal.
when alternate each time you press the pedal.
PEDAL FX ON/OFF
OFF, ON
Switches the status of function assigned to
EXP1.
EXP1.
GT-10B_e.book 122 ページ ２００８年２月２６日 火曜日 午後３時３０分