Boss Audio Systems GT-10B User Manual

 

You can freely assign functions to the GT-10B’s controllers.

 

Off, On

Turns the ASSIGN1–8 on/off. Pressing 
[MASTER/PEDAL FX] switches On and Off.

 

This selects the parameter to be changed.
Refer to “TARGET PARAMETER” (p. 127).

 

This sets the minimum value for the range in which the parameter 
can change. The value differs depending on the parameter assigned 
for TARGET PARAMETER.

 

This sets the maximum value for the range in which the parameter 
can change. The value differs depending on the parameter assigned 
for TARGET PARAMETER.

 

This selects the controller to which the function is assigned.

EXP1 PEDAL

EXP Pedal (this unit)

CTL1 PEDAL

CTL 1 pedal (this unit)

CTL2 PEDAL

CTL 2 pedal (this unit)

EXP PEDAL SW

EXP Pedal switch (this unit)

EXP2 PEDAL

Expression pedal connected to the EXP PEDAL 
2/SUB CTL 3,4 jack.

CTL3 PEDAL

footswitch connected to the EXP PEDAL 2/
SUB CTL 3,4 jack (jack Tip).

CTL4 PEDAL

Expression pedal connected to the EXP PEDAL 
2/SUB CTL 3,4 jack (jack Ring).

INTERNAL PDL

WAVE PEDAL

INPUT LEVEL

This controls the level of the signal from the IN-
PUT jack. Set the sensitivity in response to the 
level with Assign INPUT SENS.

CC#1–#31,
CC#64–#95

Control Change messages from an external 
MIDI device (1–31, 64–95)

 

This sets the behavior of the value each time the switch is operated.

Moment

The normal state is Off (minimum value), with 
the switch On (maximum value) only while the 
footswitch is depressed.

Toggle

The setting is toggled On (maximum value) or 
Off (minimum value) with each press of the 
footswitch.

 

ActRngLo: 0–126
ActRngHi: 1–127

You can set the controllable range for target 
parameters within the source’s operational 
range. Target parameters are controlled within 
the range set with ActRngLo and ActRngHi. 
You should normally set ActRngLo to 0 and 
ActRngHi to 127.

 

This sets the trigger that activates the internal pedal. *1

Patch Change

This is activated when a patch is selected.

EXP1 PDL-Low

This is actuated when the EXP Pedal is operat-
ed at minimum.

EXP1 PDL-Mid

This is activated when the EXP Pedal is de-
pressed and an intermediate value is passed.

EXP1PDL-High

This is actuated when the EXP Pedal is operat-
ed at maximum.

CTL1 PEDAL, 
CTL2 PEDAL

This is activated when the CTL 1 or 2 pedal on 
the GT-10B is depressed. 

EXP PEDAL SW

This is activated when the EXP Pedal switch on 
the GT-10B is turned on.

EXP2 PEDAL

This is activated when the expression pedal 
connected to the EXP PEDAL 2/CTL 3,4 jack is 
depressed.

CTL3 PEDAL

This is activated when the footswitch (jack Tip) 
connected to the EXP PEDAL 2/CTL 3,4 jack is 
depressed.

CTL4 PEDAL

This is activated when the footswitch (jack 
Ring) connected to the EXP PEDAL 2/CTL 3,4 
jack is depressed.

CC#1–#31, 
CC#64–#95

This is activated when the value of the Control 
Change messages (CC#01–31, 64–95) from an 
external MIDI device exceeds the middle value.

 

0–100

This controls the time needed for the assumed 
EXP Pedal to move from the returned (lifted) 
position to the depressed (lowered) position. *1

 

This selects one of the three types that determines how the assumed 
expression pedal changes. *1

 

0–100, 

BPM

–

BPM

This determines the time spend for one cycle of 
the assumed EXP Pedal. *2

When set to BPM, the value of each parameter will be set according 
to the value of the “Master BPM” (p. 122) specified for each patch. 
This makes it easier to achieve effect sound settings that match the 
tempo of the song.

 

If, due to the tempo, the time is longer than the range of allowable settings, it 
is then synchronized to a period either 1/2 or 1/4 of that time.

 

This selects one of the three types that determines how the assumed 
EXP Pedal should change. *2

Linear

Slow Rise

Fast Rise

SAW

TRIANGLE

SINE

GT-10B_e.book 126 ページ ２００８年２月２６日　火曜日　午後３時３０分