Bosch Appliances Home Security System D7412G User Manual
D9412G/D7412G | Program Entry Guide | 2.0 9000MAIN
EN | 21
Bosch Security Systems | 1/04 | 47775E
Table 13: Diagnostic Reports
Report
Selections
Description
R# SDI Dev Fail
*
Yes, No
Reports SDI device
failure.
failure.
R# SDI Dev Restl
Yes, No
Reports restoral of SDI
device failure.
device failure.
R# Watchdog
Rset
Rset
Yes, No
Reports Watchdog
Reset Event.
Reset Event.
R#
ParaChksmFail
ParaChksmFail
Yes, No
Reports parameter
checksum failure.
checksum failure.
R# Reboot
Yes, No
Reports Reboot Event.
R# Ph Line Fail
*
Yes, No
Reports failure of phone
line.
line.
R# Ph Line Rstl
Yes, No
Reports restoral of
phone line after failure.
phone line after failure.
R# AC Fail
*
Yes, No
Reports failure of AC
power to control panel.
power to control panel.
R# AC Restorl
Yes, No
Reports restoral of AC
power to control panel
after failure.
power to control panel
after failure.
R# Batt Missing
*
Yes, No
Reports Battery Missing
Detection Event.
Detection Event.
R# Battery Low
*
Yes, No
Reports low battery
power.
power.
R# Battery Rstl
Yes, No
Reports restoral of
battery power to control
panel after Missing or
Low Event.
battery power to control
panel after Missing or
Low Event.
R# Rt Comm
Fail
Fail
*
1
Yes, No
Reports failure to send
report to specific route.
report to specific route.
R# Rt Comm Rstl
Yes, No
Reports restoral of
communication to
specific route after a
failure.
communication to
specific route after a
failure.
R# Checksum
Fail
Fail
Yes, No
Reports Checksum Fail
Event.
Event.
R# Network Fail
2
Yes, No
Reports failure of
network.
network.
R# Network
Rest
Rest
2
Yes, No
Reports restoral of
network.
network.
R# Network
Cond
Cond
2
Yes, No
Reports condition of
network.
network.
1
This event covers Comm Fail Route Group and Comm
Fail Phone. If enabled, both events are sent; if disabled,
neither event is sent.
neither event is sent.
2
This event reserved for future use.
0101
0101
0101
0101
0101
Only turn on Rt Comm Fail and Rt Comm
Restore in one route group.
Restore in one route group.
Relay Reports
Selecting Yes enables sending a report when the
event occurs.
event occurs.
Table 14: Relay Reports
Report
Selections
Description
R# Sensor
Reset
Reset
Yes, No
Reports Sensor
Reset Event.
Reset Event.
R# Relay Set
Yes, No
Reports Relay
Set Event.
Set Event.
R# Relay Reset
Yes, No
Reports Relay
Reset Event.
Reset Event.
When activating an on-board relay using
PC9000, the 9000 Series Control Panel
logs and prints the event as Relay 250
(Relay A), Relay 251 (Relay B), and Relay
252 (Relay C).
PC9000, the 9000 Series Control Panel
logs and prints the event as Relay 250
(Relay A), Relay 251 (Relay B), and Relay
252 (Relay C).
AutoFunc Reports
The following prompts support customized routing
of Auto Function Reports. Selecting
of Auto Function Reports. Selecting
Yes enables a
report to be sent when the event occurs.
Table 15: Auto-Function Reports
Report
Selections
Description
R# Sked
Executed
Executed
Yes, No
Reports Sked
Executed Event.
Executed Event.
R# Sked
Changed
Changed
Yes, No
Reports Sked
Changed Event.
Changed Event.
R# Execute Fail
Yes, No
Reports a Fail to
Execute Event.
Execute Event.