Bosch Appliances Home Security System ICP-CC488 User Manual
ICP-CC488 | Installation Guide | 15.0
System Reporting Information
EN | 66
Bosch Security Systems, Inc. | 12/08 | F01U089457-02
A Sensor Trouble Restore Report is sent for Burglary
Zones when the zone is resealed or the next time the
system is disarmed (whichever happens first). A 24-
Hour Zone sends a restore signal only when it is
resealed.
Zones when the zone is resealed or the next time the
system is disarmed (whichever happens first). A 24-
Hour Zone sends a restore signal only when it is
resealed.
The Trouble code parameter has no effect on
Contact ID Format because a Sensor Trouble Report
is always reported as Event Code 380.
Contact ID Format because a Sensor Trouble Report
is always reported as Event Code 380.
If Sensor Trouble Reports are not
required, program Locations 387 and 388
as 0.
required, program Locations 387 and 388
as 0.
15.5 Zone Status – Sensor Watch
Reports
Location
389 to 390
Location
Default
Sensor Watch Report
389
4
Sensor Watch Restore Report
390 5
A Self Test Failure Report (Contact ID Event Code
307) is sent to the base station receiver when a zone
was not activated during the Sensor Watch Time
programmed in Locations 476 and 477 (refer to
Section 15.5 Zone Status – Sensor Watch Reports on
page 78). This report continues to be sent (according
to the frequency of the Sensor Watch Time) until the
fault is corrected.
307) is sent to the base station receiver when a zone
was not activated during the Sensor Watch Time
programmed in Locations 476 and 477 (refer to
Section 15.5 Zone Status – Sensor Watch Reports on
page 78). This report continues to be sent (according
to the frequency of the Sensor Watch Time) until the
fault is corrected.
To clear the fault and stop any additional reporting,
you must unseal and reseal the zone that registered
the fault. Use the Sensor Watch Time in Locations
476 and 477 to set the number of days a zone can
remain sealed without registering a fault. Refer to
Section 14.3.5 Zone Options 1 on page 61 to select
zones to be monitored by the Sensor Watch feature.
you must unseal and reseal the zone that registered
the fault. Use the Sensor Watch Time in Locations
476 and 477 to set the number of days a zone can
remain sealed without registering a fault. Refer to
Section 14.3.5 Zone Options 1 on page 61 to select
zones to be monitored by the Sensor Watch feature.
If Self Test Failure Reports are not
required, program Locations 389 and 390
as 0.
required, program Locations 389 and 390
as 0.
15.6 Zone Status – Alarm Restore Code
Location
391
Default
14
If Zone Alarm Restore Reports are required,
program this location as 14. If not, program this
location as 0.
program this location as 14. If not, program this
location as 0.
Location 392 (Section 15.7 Zone Status Reporting Options
on page 66) is ignored when programming the Alarm
Restore code and is global for all zones. A zone
Restore Report is sent only to the receiving party to
which the zone is allocated (for example, Receiver 1
or Receiver 2).
on page 66) is ignored when programming the Alarm
Restore code and is global for all zones. A zone
Restore Report is sent only to the receiving party to
which the zone is allocated (for example, Receiver 1
or Receiver 2).
15.7 Zone Status Reporting Options
Location
392
0
No zone status reports allowed
1
Report to Receiver 1
2
Report to Receiver 2
4
Report to both Receiver 1 and Receiver 2
8
Report to Receiver 2 only if Receiver 1 fails
This location is set by default to report only to
Receiver 1. You can select whether Zone Status
Reports are sent to Receiver 1, Receiver 2, or both,
Receiver 2 only when Receiver 1 fails, or no
reporting.
Receiver 1. You can select whether Zone Status
Reports are sent to Receiver 1, Receiver 2, or both,
Receiver 2 only when Receiver 1 fails, or no
reporting.
For a partitioned ICP-CC488 Control Panel, this
location is ignored if Option 1 is selected in Location
501 (refer to Section 19.3.2 Partitioning Options 2 on
page 85).
location is ignored if Option 1 is selected in Location
501 (refer to Section 19.3.2 Partitioning Options 2 on
page 85).
15.8 RF Supervision Time
Location
393
Default
0
0
Disable RF Supervision Time Reports
1 to 15
Increments of 6 hours (0 to 90 hours)
An RF Supervision Failure Report (Contact ID Event
Code 307) is sent to the base station receiver when
the wireless receiver has not received a signal from
any RF wireless zone during the RF Supervision
Time. This report continues to be sent (according to
the frequency of the RF Supervision Time) until the
fault is corrected.
Code 307) is sent to the base station receiver when
the wireless receiver has not received a signal from
any RF wireless zone during the RF Supervision
Time. This report continues to be sent (according to
the frequency of the RF Supervision Time) until the
fault is corrected.
To clear the fault and stop additional reporting:
Unseal and reseal the zone that registered the fault.
Refer to Section 3.13 Fault Descriptions on page 18 for
more information.
Unseal and reseal the zone that registered the fault.
Refer to Section 3.13 Fault Descriptions on page 18 for
more information.
If RF Supervision Failure Reports are not
required, program Location 393 as 0.
required, program Location 393 as 0.
15.9 RF Low Battery Report
Location
394 to 395
Location
Default
RF Low Battery Report
394
6
RF Low Battery Restore Report
395 8
An RF Low Battery Report (Contact ID Event Code
384) is sent to the base station receiver when the
battery voltage on a wireless zone falls below
approximately 2.4 VDC. An RF Low Battery Restore
Report is sent on the first valid signal after the
battery is replaced.
384) is sent to the base station receiver when the
battery voltage on a wireless zone falls below
approximately 2.4 VDC. An RF Low Battery Restore
Report is sent on the first valid signal after the
battery is replaced.
15.10 RF Receiver Trouble Report
Location
396 to 397
Location
Default
Tens digit
396
7
Units digit
397 9