Black & Decker EasyEdge BDPE200B User Manual

filling WitH paint (F, G & H)

Do not use the unit without the paint 

applicator securely attached. 

note: Use drop cloths to protect your floors and anything else in 

the room that you do not want accidentally splattered with paint.

note: Skin that forms on the top of paint can clog the 

paint edger. Remove this skin before mixing. Strain using a 

funnel with a filter attached or through hosiery to remove any 

impurities that could clog the system.

• Pull locking tabs (12) on the fill sleeve (11) down, slide the 

paint tube into the fill sleeve as shown in figure f.

• Squeeze and hold locking tabs together on the fill sleeve 

to secure the paint tube in place. Lower the tip of the fill 

sleeve into the paint container.

• Fill the paint tube by slowly pulling back the plunger as 

shown in figure g.

note: Do not over pull the plunger. The paint tube has a 

stop which makes it very difficult to pull the plunger out.

• Remove the paint tube from the fill sleeve. pull the plunger 

note: Wipe any excess paint from the paint tube before 

reinserting into the paint edger.

note: Paint sleeve will have excess paint on it. Store on 

lid or on the side of the paint can with its built in clips (13) as 

shown in figure H.
painting WitH tHe paint eDger (I, J & K)

• Install the paint applicator.

• Set the flow control knob (3) to the minimum flow setting of 

“1” as shown in figure i.

• Fill the paint tube with paint.

• Install the paint tube in the main body.

• Pull the trigger (2). Paint will start to flow slowly into the 

paint applicator as shown in figure J. If no paint appears, 

increase flow rate by turning flow control knob in single 

numerical increments towards 10 until paint saturates the 

paint applicator pad.

note: Once paint is showing on the paint applicator’s foam 

pad, it is ready to use.

• Keeping the paint applicator flat against the wall. 

• Start away from the edge you wish to paint to ensure paint 

coverage is appropriate. Pull the trigger and slowly move 

the paint edger in toward the edge you are painting as 

shown in figure K.

• Increase the flow of paint to the desired amount by turning the 

flow control knob in single numerical increments from 1-10.

note: Do not push too hard or the unit will have poor 

coverage. The unit will sound overloaded when pushed too 

hard. Let the paint applicator float over the surface.

note: Temperature and the type of paint being used will 

affect the flow rate. Alter both the flow of paint and the speed 

at which you move the paint edger to achieve the best results.

• Using too much paint or moving the edger too slowly 

will cause a bead of paint to appear on the edges of the 

painted surface. Using a paint brush, roller or the edger’s 

applicator pad unpowered on the painted surface, smooth 

the bead lines with soft strokes as shown in figure l.

• Using too little paint or moving the edger too quickly will 

result in thin coverage and possible streaking. Increase 

the flow of paint to the desired amount by turning the flow 

control knob in single numerical increments towards 10. 

note: Do not pick up or hold paint edger by the paint tube.

• For optimum performance keep the paint edger 

perpendicular to the surface being painted as shown in 

figure m. If the rear of the paint edger is tilted up or down 

this will overload the unit and it will result in poor paint 

coverage and sound under powered.

• Always hold the paint applicator flat against the surface.

• The paint edger can be angled left or right to enable a clear 

view of the edge being painted.

• Always use steady movements.

• As required, wipe excess paint from the edges of the paint applicator.

• If the paint applicator is sliding on the surface, apply less paint 

by turning the flow control knob to a lower numerical setting.

• When not in use, pull the plunger drive to the back of the main body of the paint edger and 

clip it in place.

• When leaving the paint edger unattended for a longer period of time, wrap the paint 

applicator in a plastic bag to prevent drying, removing as much air as possible from the bag.

• Make sure the type of paint you use can be cleaned with a warm water and soap solution.

• Pull the plunger drive to the back of the main body of the paint edger and clip it in place.

• Slide the paint tube out of the main body of the paint edger.

• Hold the paint tube over the paint can and gently push down on the plunger to return paint to the can.

note: Do not store paint in the paint tube.

Your Black & Decker cordless appliance has been designed to operate over a long period of 

time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper appliance care and regular cleaning.

 Before performing any maintenance or cleaning on cordless appliances 

switch off and remove the batteries from the appliance.

• The paint applicator should be removed when storing the product.

• Wipe the paint edger main body using a soft damp cloth.

• For stubborn marks you can use a mild solution of soap and water to dampen your cloth.

• Paint applicator and paint tube can be washed in warm soapy water, however this will 

have a negative effect on the performance of your tool. To maintain the highest level of 

performance the paint applicator and paint tube should be replaced after every job.

• Unit will not run.   

• Batteries inserted incorrectly. 

• Make sure to match (+) and  

 

 

 

 

 

 

 

(-) terminals correctly.

   

 

 

• Batteries need replacing.   

• Insert 3 fresh 1.5 volt AA    

 

      batteries.

• Paint is not flowing out.  • Flow control knob set too low. 

• Increase setting on flow    

 

      control 

knob 

until 

paint 

flows 

 

      out 

of 

applicator 

pad. 

 

 

 

 

 

• Paint tube not assembled   

• Confirm that paint tube and  

 

 

  properly. 

   plunger 

are 

aligned 

with 

 

      plunger 

drive 

tip.

   

 

 

• Plunger drive not pushed forward.  • Ensure plunger drive has 

 

      been 

unclipped 

from 

the 

 

 

      main 

body. 

• Paint coming out too fast.  • Flow control knob set too high. 

• Decrease setting on flow   

 

      control 

knob.

• Paint coming out too slow.  • Flow control knob set too low. 

• Increase setting on flow    

 

      control 

knob.

• Paint applicator leaves 

• Flow control knob set too high. 

• Decrease setting on flow  

beads of paint on each end. 

 

 

 

control knob.

   

 

 

• Moving the edger too slowly. 

• Use a paint brush to

 

 

      smooth 

out 

the 

paint 

beads

For assistance with your product, visit our website www.blackanddecker.com for the location of the 

service center nearest you or call the BLACK & DECKER help line at 1-800-544-6986.

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; 

never immerse any part of the tool into a liquid. important: To assure product SAFETY 

and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized 

service centers or other qualified service personnel, always using identical replacement parts.

The use of any accessory or attachment not recommended may be hazardous.

The performance of your tool depends on the accessory used. Black & Decker accessories are 

engineered to high quality standards and designed to enhance the performance of your tool. By 

using these accessories you will get the very best from your tool.

• Accessory numbers BDPE1020, BDPE3020 & BDPE1015 Recommended accessories for 

use with your tool are available from your local dealer or authorized service center. If you need 

assistance regarding accessories, please call: 1-800-544-6986.

All Black & Decker Service Centers are staffed with trained personnel to provide customers 

with efficient and reliable power tool service. Whether you need technical advice, repair, or 

genuine factory replacement parts, contact the Black & Decker location nearest you. To find 

your local service location, refer to the yellow page directory under “Tools—Electric” or call: 

Black & Decker (U.S.) Inc. warranties this product to be free from defects in material or workmanship 

for a period of two (2) years following the date of purchase, provided that the product is used in a 

home environment.  This limited warranty does not cover failures due to abuse, accidental damage or 

when repairs have been made or attempted by anyone other than Black & Decker and its Authorized 

Service Centers. A defective product meeting the warranty conditions set forth herein will be replaced or 

repaired at no charge in either of two ways: The first, which will result in exchanges only, is to return the 

product to the retailer from whom it was purchased (provided that the store is a participating retailer).

Returns should be made within the time period of the retailer’s policy for exchanges. Proof of purchase 

may be required. Please check with the retailer for its specific return policy regarding time limits for 

returns or exchanges. The second option is to take or send the product (prepaid) to a Black & Decker 

owned or authorized Service Center for repair or replacement at Black & Decker’s option. Proof of 

purchase may be required.  Black & Decker owned and authorized service centers are listed under 

“Tools–Electric” in the yellow pages of the phone directory or online at www.blackanddecker.com.

This warranty does not apply to accessories. This warranty gives you specific legal rights and you may 

have other rights which vary from state to state. Should you have any questions, contact the manager 

of your nearest Black & Decker Service Center. This product is not intended for commercial use, and 

accordingly, such commercial use of this product will void this warranty. All other guarentees, express 

or implied, are hereby disclaimed.

latin america: This warranty does not apply to products sold in Latin America.  For products 

sold in Latin America, check country specific warranty information contained in the packaging, call 

the local company or see the website for such information.

Imported by 

Black & Decker (U.S.) Inc.,  

701 E. Joppa Rd. 

Towson, MD 21286 U.S.A.

directives. Le non-respect des avertissements et des directives pourrait se solder 

par un choc électrique, un incendie et/ou une blessure grave.

  Le terme «outil électrique» cité dans les avertissements se rapporte à votre outil 

électrique à alimentation sur secteur (avec fil) ou par piles (sans fil).

Il est important que vous lisiez et compreniez ce mode d’emploi. Les informations qu’il 

contient concernent VOTRE SÉCURITÉ et visent à ÉVITER TOUT PROBLÈME. Les  

symboles ci-dessous servent à vous aider à reconnaître cette information.

Indique une situation dangereuse imminente qui, si elle n’est pas évitée, 

causera la mort ou des graves blessures.

Indique une situation potentiellement dangereuse qui, si elle 

n’est pas évitée, pourrait causer la mort ou de graves blessures.

 Indique une situation potentiellement dangereuse qui, si elle 

n’est pas évitée, pourrait causer des blessures mineures ou modérées.

aviS : Utilisé sans le symbole d’alerte à la sécurité, indique une situationvpotentiellement 

dangereuse qui, si elle n’est pas évitée, peut résulter en des dommages à la propriété.

Si des questions ou des problèmes surgissent après l’achat d’un produit Black & Decker, consulter le site Web 

www.blackanddecker.com/instantanswers 

pour obtenir des réponses instantanément 24 heures par jour. Si la réponse est introuvable ou en l’absence 

d’accès à l’Internet, composer le 1 800 544-6986 de 8 h à 17 h HNE, du lundi au vendredi, pour parler avec un 

agent. Prière d’avoir le numéro de catalogue sous la main lors de l’appel.