Bosch Appliances Video Game Controller d9412gv3 User Manual
D9412GV3/D7412GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters
EN | 13
Bosch Security Systems, Inc. | 10/11 | F01U170807-02
If you program the primary phone number with a
sequence to temporarily disable Call Waiting
(typically *70 pause, but verify with the phone service
provider) followed by the phone number, you should
program the backup phone number without the Call
Waiting cancel sequence. If the subscriber cancels
Call Waiting without notifying their alarm installing
company, the control panel can still send reports
using the backup number.
sequence to temporarily disable Call Waiting
(typically *70 pause, but verify with the phone service
provider) followed by the phone number, you should
program the backup phone number without the Call
Waiting cancel sequence. If the subscriber cancels
Call Waiting without notifying their alarm installing
company, the control panel can still send reports
using the backup number.
Dialing a Call Waiting sequence on a
non-Call Waiting line prevents the system
from dialing the central station receiver
successfully.
non-Call Waiting line prevents the system
from dialing the central station receiver
successfully.
Example: If the central station telephone
number is 555-1234, and the primary
Route Group destination is Phone 1,
program Phone 2 with the following
sequence: *70C5551234.
number is 555-1234, and the primary
Route Group destination is Phone 1,
program Phone 2 with the following
sequence: *70C5551234.
Keypad Programming of Phone #
D1255
1. Refer to Figure 1 on page 7 to access Keypad
1. Refer to Figure 1 on page 7 to access Keypad
Programming and navigate to the PHONE
NUMBERS option.
NUMBERS option.
2. At the PHONE 1 - 4 prompt, enter the phone
number you wish to configure and press [ENT].
The current phone number shows.
The current phone number shows.
If the current phone number is longer
than 20 characters, use the [PREV] and
[NEXT] keys to scroll to view the
additional characters.
than 20 characters, use the [PREV] and
[NEXT] keys to scroll to view the
additional characters.
3. Press [ENT] to change the phone number.
4. The [PREV] button acts as a [Backspace] key and
4. The [PREV] button acts as a [Backspace] key and
the [COMMAND] key scrolls through special
characters. Press [PREV] to delete the characters
of the phone number, and then enter the new
phone number. Press [COMMAND] to cycle
through the special dialing characters {*, #, C, D},
then press [NEXT] to choose a character.
characters. Press [PREV] to delete the characters
of the phone number, and then enter the new
phone number. Press [COMMAND] to cycle
through the special dialing characters {*, #, C, D},
then press [NEXT] to choose a character.
5. Press [ENT] to save the phone number.
6. When the keypad reads PARAMETER SAVED,
6. When the keypad reads PARAMETER SAVED,
your selection has been configured.
D1260
1. Refer to Figure 2 on page 8 to access Keypad
1. Refer to Figure 2 on page 8 to access Keypad
Programming and navigate to the Phone
Numbers option and press the corresponding
softkey.
Numbers option and press the corresponding
softkey.
2. At the Phone (1-4) prompt, enter the phone
number you wish to configure and press [ENTER].
The current phone number shows.
The current phone number shows.
If the current phone number is longer
than 20 characters, the Previous and
Next softkeys appear. Use the softkeys to
scroll to view the additional characters.
than 20 characters, the Previous and
Next softkeys appear. Use the softkeys to
scroll to view the additional characters.
3. Press the Edit softkey to change the phone
number.
4. The Pause (3 sec pause - "C") and DT Detect
(Dial Tone Detect - "D") softkeys enter special
characters. The Backspace softkey allows you to
erase characters. The Clear softkey allows you to
clear the entire phone number. The [COMMAND]
and [ENTER] keys allow you to enter an * or a #.
Use the softkeys, the number buttons, and the
[COMMAND] and [ENTER] keys on the keypad to
enter the new phone number.
characters. The Backspace softkey allows you to
erase characters. The Clear softkey allows you to
clear the entire phone number. The [COMMAND]
and [ENTER] keys allow you to enter an * or a #.
Use the softkeys, the number buttons, and the
[COMMAND] and [ENTER] keys on the keypad to
enter the new phone number.
5. Press the Save softkey.
When the keypad reads Parameter Saved, your
selection has been configured.
When the keypad reads Parameter Saved, your
selection has been configured.