INSTEON I/O LINC 73210 Leaflet

Page of 1
Page 1 of 1 
Rev. 04-06-2009 
 
 
 
 
 
 
 
Using an INSTEON Device to Trigger a Telephone Alert 
1) 
Follow Phone Dialer’s User’s Instructions on Installation and Programming (disregard instructions referring to other Skylink products) 
2) 
Plug your I/O Linc into an un-switched outlet near your Phone Dialer 
I/O Linc’s Status LED will turn on
 
3) 
Remove the pre-stripped plastic insulation from included connection wire 
4) 
Insert one of connection wire’s stripped leads into I/O Linc’s N/C terminal (see Figure 1) 
5) 
Insert connection wire’s other stripped lead into I/O Linc’s Common terminal (see Figure 1) 
6) 
Open Phone Dialer’s cover and insert connection wire into Phone Dialer’s N.C. terminals (remove existing metal jumper). Close Phone Dialer’s cover. 
Link INSTEON Controller/Sensor to I/O Linc 
7) 
Press & hold the Set button on the INSTEON device you want to trigger a telephone alert 
Controller’s Status LED will begin blinking
 
8) 
Press & hold I/O Linc’s Set button until it beeps (about 3 seconds) 
I/O Linc will beep once again to confirm linking; Controller’s LED will stop blinking
 
Set I/O Linc into Momentary Mode 
9) 
Press & hold I/O Linc’s Set button until it beeps (about 3 seconds) 
10)  Press & hold I/O Linc’s Set button until it beeps (about 3 seconds) 
11)  Press & hold I/O Linc’s Set button until it beeps (about 3 seconds) 
I/O Linc’ Status LED will stop blinking
 
12)  Press & hold I/O Linc’s Set button until it beeps (about 3 seconds) 
13)  Press & hold I/O Linc’s Set button until it beeps (about 3 seconds) 
14)  Press & hold I/O Linc’s Set button until it beeps (about 3 seconds) 
I/O Linc’ Status LED will stop blinking
 
15)  Test by turning your INSTEON Controller/Sensor On or Off 
Phone Dialer will call according to its programming in step 1 in response to INSTEON On and Off commands 
Introduction
 
I/O Linc – INSTEON Telephone Alert Kit enhances your INSTEON network by using a 
phone dialer along with an I/O Linc to immediately notify you and/or neighbors and loved 
ones via telephone and/or cell phone that there is something happening at your home 
requiring your attention. Recipients of the automated phone call will hear a user recorded 
message identifying the concern. By linking an INSTEON motion sensor, door/window, 
and/or leak/flood sensor to the I/O Linc, the phone dialer can call you if any unauthorized 
movement, door/window activity or a leak takes place. Any device that transmits an 
INSTEON signal can be used to trigger the I/O Linc - INSTEON Telephone Alert Kit to call 
out simply by linking the devices together. 
Quick-Start Guide
 
I/O Linc
TM
 – INSTEON Telephone Alert Kit 
Model: 73210 
Telephone Alert of INSTEON Activity
 
SmartLabs Limited Warranty – SmartLabs warrants to original consumer of this product for a 
period of 2 years from date of purchase, this product will be free from defects in material & 
workmanship & will perform in substantial conformity with its owner's manual. Warranty shall 
not apply to defects caused by misuse or neglect.   
U.S. Patent No. 7,345,998, International patents pending ©Copyright 2009 
SmartLabs, 16542 Millikan Ave., Irvine, CA 92606, 1-800-SMARTHOME (800-762-7846)
Connection 
Wire 
Phone Dialer 
Power Supply 
Set Button / Status LED 
Phone Cord 
Screw Terminals
Questions? 
Click: For Advanced Features and X10 compatibility, refer to I/O Linc’s Owner’s Manual:
  
http://wiki.smarthome.com/index.php?title=I/O_Linc_-_INSTEON_Low_Voltage_/_Contact_Closure_Interface_Owner%27s_Manual
 
Call: Friendly tech support @ 1-800-SMARTHOME (800-762-7846) 
I/O Linc’s Screw Terminals 
5V GND Sense  N/C 
N/O 
Common 
Volts 
Ground 
Sensor 
Input 
Normally 
Closed 
Normally 
Open 
Switches 
between N/O 
and N/C 
Items you will Need 
1) Wire 
stripping 
tool 
 
Figure 1 
Wiring I/O Linc to Phone Dialer
 
Connection 
Wire 
Phone 
Dialer
N.C. 
Terminals
N/C / Common 
Terminals 
I/O Linc (screwdriver 
included)