Sunfire TGR401 User Manual
User's Manual
14
CHAPTER 1
Observe the following precautions
when choosing a location for your
TGR-401:
TGR-401:
Make sure the TGR-401 has
good ventilation. Do not cover
any of the ventilation slots, or
t the receiver inside a sealed
cabinet without good air ow.
any of the ventilation slots, or
t the receiver inside a sealed
cabinet without good air ow.
• Protect it from pro longed ex po sure
to direct sunlight and other direct
sources of heat, such as heating
vents and ra di a tors.
sources of heat, such as heating
vents and ra di a tors.
• Do not expose the unit to rain or
moisture. If uid or a foreign object
should enter the unit, immediately
turn off the power and contact your
Sun re Dealer.
should enter the unit, immediately
turn off the power and contact your
Sun re Dealer.
• Avoid excessive exposure to ex-
treme cold or dust.
• Do not place heavy objects on top
of the unit.
AC Power Con sid er ations
Ensure that the unit is plugged into
an outlet capable of supplying the cor-
rect voltage speci ed for your model.
rect voltage speci ed for your model.
Care
If you need to clean the front sur-
face, rst turn off the power and then
use a soft dry cloth, rubbing with the
grain. Be careful not to scratch the
display window.
use a soft dry cloth, rubbing with the
grain. Be careful not to scratch the
display window.
Connection Tips
Before setting up your new sys tem,
please consider the following :
Always make sure that your
com po nents are all turned
OFF, or unplugged before
making or changing any
connec tions.
com po nents are all turned
OFF, or unplugged before
making or changing any
connec tions.
• Whenever possible, route the
power cords away from the signal
cables or speaker wires to pre vent
any hum or in ter fer ence heard in
the speak ers.
cables or speaker wires to pre vent
any hum or in ter fer ence heard in
the speak ers.
• Choose reliable hookup cables.
They should be fully shield ed and
as short as pos si ble.
as short as pos si ble.
• Use quality coaxial digital cables
to connect the TGR-401 to any
source equipment which has co-
axial digital outputs.
source equipment which has co-
axial digital outputs.
• Some patch cords can be a very
tight t and there is usually a
preferred method of getting them
off. Some have to be removed
with a twisting action. Be gentle or
you may dam age the jacks of your
TGR-401, or other com po nents.
preferred method of getting them
off. Some have to be removed
with a twisting action. Be gentle or
you may dam age the jacks of your
TGR-401, or other com po nents.
• Some audiophile cables should be
hooked up in one direction, these
are usually marked with arrows.
are usually marked with arrows.
• It is usual for the right channel
patch cord plugs to be red and
the left channel con nec tions to be
white, grey or black. Com pos ite
video con nec tions are usually yel-
low.
the left channel con nec tions to be
white, grey or black. Com pos ite
video con nec tions are usually yel-
low.
Installation
Video Connections
The TGR-401 has four types of
video connections: composite video,
S-video, component video and HDMI.
Choose component or S-video if your
video system supports it, as this will
give better picture quality than com-
posite video.
S-video, component video and HDMI.
Choose component or S-video if your
video system supports it, as this will
give better picture quality than com-
posite video.
When an audio/video component
is selected, the audio will play in your
system and the video will be switched
to a video input of your TV mon i tor.
system and the video will be switched
to a video input of your TV mon i tor.
You must have the TV connected
in order to see the On Screen Display
(OSD). No OSD is available on HDMI.
(OSD). No OSD is available on HDMI.