Sony Water Dispenser 2 User Manual
231
Setup Relating to Operations From the Control Panel
Ch
apt
apt
er 16
E
ngin
eering Se
tup
2
Make the following settings as required.
Operation mode of the [ALL] button in the transition control block:
To specify the next transition to be selected by pressing the [ALL]
button in the transition control block, press the next transition you
want to select, turning it on, in the <Next Trans All> group. If
everything here is set to OFF, then pressing the [ALL] button does not
change the specification of the next transition.
button in the transition control block, press the next transition you
want to select, turning it on, in the <Next Trans All> group. If
everything here is set to OFF, then pressing the [ALL] button does not
change the specification of the next transition.
Operation mode during an auto transition: For the operation mode
when the [AUTO TRANS], [TAKE] or [FTB] button is pressed once
more during an auto transition, select [Continue] or [Cancel] in the
<Auto Trans/Take> group.
Continue: Continue the auto transition.
Cancel: Cancel the auto transition and return to the state before
starting the auto transition.
more during an auto transition, select [Continue] or [Cancel] in the
<Auto Trans/Take> group.
Continue: Continue the auto transition.
Cancel: Cancel the auto transition and return to the state before
starting the auto transition.
Operation mode during keyframe execution: For the operation mode
when the [RUN] button is pressed once more during effect execution,
select [Continue] or [Cancel] in the <RUN> group.
Continue: Continue the execution.
Cancel: Cancel the execution and return to the state before starting the
execution.
select [Continue] or [Cancel] in the <RUN> group.
Continue: Continue the execution.
Cancel: Cancel the execution and return to the state before starting the
execution.
Interchanging the [AUTO TRANS] and [CUT] buttons: To
interchange the [AUTO TRANS] and [CUT] buttons in the transition
control block, press the [Auto Trans/Cut Swap] button, turning it on.
control block, press the [Auto Trans/Cut Swap] button, turning it on.
[UTIL] button operation mode: To set the operation mode of the [UTIL]
button in the cross-point control block, press either of the following in
the <Util Button> group.
Hold: Acts as a utility button while held down, changing the
assignment of the cross-point button rows.
Lock: For the key rows, each time the button is pressed the cross-point
button assignment toggles between the utility assignment and the
normal assignment. The background A and B rows are fixedly
assigned to the A and B rows, even if the [UTIL] button is pressed.
(For details, see “Names and Functions of Parts of the Control
Panel” in Chapter 2 (Volume 1).)
the <Util Button> group.
Hold: Acts as a utility button while held down, changing the
assignment of the cross-point button rows.
Lock: For the key rows, each time the button is pressed the cross-point
button assignment toggles between the utility assignment and the
normal assignment. The background A and B rows are fixedly
assigned to the A and B rows, even if the [UTIL] button is pressed.
(For details, see “Names and Functions of Parts of the Control
Panel” in Chapter 2 (Volume 1).)
Transition preview operation mode: For the operation mode of the
[TRANS PVW] button, select [Lock] or [Hold] in the <Trans Pvw>
group. The setting as to whether to use the “One-time mode” in which
the transition preview terminates when the transition completes, or to
use button control, is made on the switcher side (see page 244).
group. The setting as to whether to use the “One-time mode” in which
the transition preview terminates when the transition completes, or to
use button control, is made on the switcher side (see page 244).
Operation mode of the [XPT HOLD] buttons in the key rows: Set the
operation mode of the [XPT HOLD] buttons in the key rows in the
<Key Bus Xpt Hold> group, as follows.
Normal: The <Xpt Hold Mode> in the Switcher>Key/Wipe/FM
menu is enabled.
<Key Bus Xpt Hold> group, as follows.
Normal: The <Xpt Hold Mode> in the Switcher>Key/Wipe/FM
menu is enabled.