Sony PCS-G70 User Manual
48
Registering Local Information
PCS-G70/G70P
3-863-237-11 (1)
Y:\04C08060_passage\EDIT\04SET.FM
masterpage:Left
When the remote videoconferencing system
does not support the audio mode selected by
the local site, the mode automatically becomes
“G.711”.
does not support the audio mode selected by
the local site, the mode automatically becomes
“G.711”.
Restrict
Allows you to select the ISDN transmission
rate at dialing. If you set. “Individual
Settings” to “On” on page 1 of the
Communication Setup menu, you can
perform this setting individually for
transmission, reception, and multipoint
conferencing.
Auto: Select when connecting a remote
Allows you to select the ISDN transmission
rate at dialing. If you set. “Individual
Settings” to “On” on page 1 of the
Communication Setup menu, you can
perform this setting individually for
transmission, reception, and multipoint
conferencing.
Auto: Select when connecting a remote
party via a normal ISDN line.
56K: Select when connecting a remote party
located in a region or country where the
ISDN transmission rate is 56 Kbps.
ISDN transmission rate is 56 Kbps.
The system is set to connect an ISDN line at the
transmission rate of 64 Kbps by default.
However, some countries, such as the USA,
and some regions may use the ISDN
transmission rate of 64 Kbps and 56 Kbps. You
may not communicate with such countries or
regions at 64 Kbps, so you must therefore set
“Restrict” to “56K” before dialing.
transmission rate of 64 Kbps by default.
However, some countries, such as the USA,
and some regions may use the ISDN
transmission rate of 64 Kbps and 56 Kbps. You
may not communicate with such countries or
regions at 64 Kbps, so you must therefore set
“Restrict” to “56K” before dialing.
Page 3/3
Far End Camera Control
Allows you to select whether to enable the
control of each other's cameras from each
other's site.
Allows you to select whether to enable the
control of each other's cameras from each
other's site.
On: Enables the control of each other's
cameras. This is the default setting.
Off: Disables the control of each other's
cameras.
cameras.
T.120 Data
Allows you to select whether to perform data
conferences with the T.120 standard using
NetMeeting (only for ISDN connections). If you
set “Individual Settings” to “On” on page 1 of the
Communication Setup menu, you can perform
this setting individually for transmission,
reception, and multipoint conferencing.
On: Enables T.120 data conferences.
Off: Disables T.120 data conferences.
Allows you to select whether to perform data
conferences with the T.120 standard using
NetMeeting (only for ISDN connections). If you
set “Individual Settings” to “On” on page 1 of the
Communication Setup menu, you can perform
this setting individually for transmission,
reception, and multipoint conferencing.
On: Enables T.120 data conferences.
Off: Disables T.120 data conferences.
For details about T.120 data conferences,
see “Conducting a Data Conference Using
see “Conducting a Data Conference Using
NetMeeting – T.120 Data Conference” on
page 138.
page 138.
H.239
Allows you to select whether you can use the
dual video presentation mode based on the
H.239 standard. If you set “Individual
Settings” to “On” on page 1 of the
Communication Setup menu, you can
perform this setting individually for
transmission, reception, and multipoint
conferencing.
On: Enables the dual video presentation
Allows you to select whether you can use the
dual video presentation mode based on the
H.239 standard. If you set “Individual
Settings” to “On” on page 1 of the
Communication Setup menu, you can
perform this setting individually for
transmission, reception, and multipoint
conferencing.
On: Enables the dual video presentation
mode based on the H.239 standard.
Off: Disables the dual video presentation
mode based on the H.239 standard.
Page 4/4
This page is only displayed when MCU
software (page 169) is installed.
software (page 169) is installed.
Multipoint Mode
Allows you to select whether to conduct
multipoint videoconferences.
Allows you to select whether to conduct
multipoint videoconferences.
Auto: Switch from two-point
videoconference to multipoint
videoconference automatically.
videoconference automatically.
Note
Note
Far End Camera Control
On
Page:
3/3
Off
On
T. 120 Data
H 239
Communication
Save
Cancel
Multipoint Mode
Auto
Page:
4/4
Split
Broadcast Mode
Communication
Save
Cancel
Automatic
Split
Full Screen
Sender Screen