Roland BR-600 User Manual
63
Re-recording Only a Mistake (Punch-in/out)
Re
v0.10
v0.10
Section 1
The repeat function (p. 58) allows you to play a certain
portion of a song (the loop portion) over and over again.
portion of a song (the loop portion) over and over again.
If you used auto punch in/out together with the repeat
function, the portion will be repeated so the result of the
recording can be heard right away.
function, the portion will be repeated so the result of the
recording can be heard right away.
If the recording did not sound as you wished, simply press
[REC] and redo the recording.
[REC] and redo the recording.
Using the repeat function and auto punch in/out together
in this manner to repeatedly perform recording is known as
“loop recording.”
in this manner to repeatedly perform recording is known as
“loop recording.”
* For details on how to set the portion where recording will
occur (the portion between the punch-in and punch-out
positions), refer to “Auto punching in and out” above.
positions), refer to “Auto punching in and out” above.
Before you begin recording, you will need to set the starting
and ending position of the portion to be repeated.
and ending position of the portion to be repeated.
* The portion to be repeated should contain the portion that
you wish to re-record (the portion between the punch-in and
punch-out points).
punch-out points).
fig.01-240
If the portion to be re-recorded is not fully contained in the
repeat portion, the recording may not start or end as desired.
repeat portion, the recording may not start or end as desired.
As an example of use, the explanation below assumes you
are using the auto punch in/out to re-record a portion of
track 1, which is a track to which you have already
recorded.
are using the auto punch in/out to re-record a portion of
track 1, which is a track to which you have already
recorded.
1
Press REC TRACK [1].
REC TRACK [1] lights alternately in orange and green.
2
Place the fader for track 1 at the location shown below.
fig.01-180
3
of the song and adjust the volume of the input source
using the REC LEVEL dial.
Listen to the track you will be re-recording and the
input source and adjust the volume of the input source
so that it is the same level as the track.
input source and adjust the volume of the input source
so that it is the same level as the track.
4
Press [STOP].
5
Press AUTO PUNCH [ON/OFF].
The button lights, showing that the auto punch in and
out have been set.
out have been set.
6
When you are ready to record, press [REC], then press
[PLAY] to begin recording.
After you press [PLAY], you can record from the time
the first punch-in is reached until the time the punch-
out is reached. Re-record the portion as desired.
the first punch-in is reached until the time the punch-
out is reached. Re-record the portion as desired.
When the song is repeated, you can check the result of
what you just recorded. If the recording is not satisfactory,
press [REC] and perform the recording again.
what you just recorded. If the recording is not satisfactory,
press [REC] and perform the recording again.
7
Press [STOP] to stop recording.
* During updating, “Keep power on!” appears in the upper
line of the display, while the lower line shows what is being
processed.
processed.
8
Press [REPEAT] to make the button go dark.
9
Press AUTO PUNCH [ON/OFF] to make the button
go dark.
Repeatedly Recording Over the
Same Location (Loop Recording)
Same Location (Loop Recording)
■
Setting the portion to be
repeated
repeated
■
How to record
Playback
Playback
Repeat
Repeat Start
(A)
Punch-In
Punch-Out Repeat End
(B)
Time
Recording
BR600_e2 63 ページ ２００６年４月１７日 月曜日 午前９時３分