Charmglow 720-0289 User Manual

 

12

Only the pressure regulator and hose assembly supplied 

with the grill should be used. Any replacement pressure, 

regulator and hose assembly must be specified by the grill 

manufacturer. 

Do not attempt to use a natural gas supply unless the grill 

has been pre-configured for natural gas use. 

 

Total gas consumption (per hour) of 720-0289 grill with all 

burners on “HI”: 

 

Main burners   

40,000 Btu/hr. 

Sear burner        18,000 Btu/hr 

Side burner        12,000 Btu/hr. 

Rotisserie burner 

15,000 Btu/hr. 

Total  

 

     85,000 Btu/hr. 

 

The installation of this appliance must conform with local 

codes or, in the absence of local codes, with the national 

fuel gas code, ANSI Z223.1 Installation in Canada must be 

in accordance with the Standard CAN/CG A-B149.2 

(installation code for gas burning appliances and 

equipment) and local codes. 

 

A dented or rusty LP Gas Cylinder may be hazardous and 

should be checked by your LP supplier. Never use a 

cylinder with a damaged valve. The LP gas cylinder must be 

constructed and marked in accordance with the 

specifications for LP gas cylinders of the U.S. Department 

of Transportation (DOT), or the National Standard of 

Canada, CAN/CSA-B339, Cylinders, Spheres and Tubes for 

Transportation of Dangerous Goods; and Commission. 

 

The 20lb. cylinder must be provided with a shut off valve 

terminating in an LP gas supply cylinder valve outlet 

specified, as applicable, for connection type QCC1 is the 

standard for compressed gas cylinder valve outlet and inlet 

connection ANSI/CGA-V-1. 

 

The cylinder supply system must be arranged for vapor 

withdrawal. The cylinder must include a collar to protect the 

cylinder valve. 

Manifold pressure: (operating): 10” water column (W.C.), 

(non-operating): 11.2” water column (W.C.).

 

 

LP Gas Cylinder must be fitted with Overfill Protection Device 

(OPD). 

 

Ensure that the black plastic grommets on the LP cylinder 

valve are in place and that the hose does not come into 

contact with the grease tray or the grill head. 

Your grill is equipped with gas supply orifices for use only with 

liquid propane gas. It is also equipped with a high capacity 

hose/regulator assembly for connection to a standard 20lb. LP 

cylinder (18-1/4” high, 12-1/4” diameter). 

 

To connect the L.P. gas supply cylinder: 

1.  Make sure tank valve is in its full off position (turn 

clockwise to stop). 

2.  Check tank valve to ensure it has proper external male 

threads (type 1 connection per ANSIZ21.81). 

3.  Make sure all burner valves are in the off position. 

4.  Inspect valve connections, port and regulator assembly. 

Look for any damage or debris. Remove any debris. 

Inspect hose for damage. Never attempt to use damaged 

or obstructed equipment. See your local LP gas dealer for 

repair. 

5.  When connecting regulator assembly to the valve, hand 

tighten the nut clockwise to a complete stop. Do not use a 

wrench to tighten. Use of a wrench may damage the 

quick coupling nut and result in a hazardous condition. 

6.  Open the tank valve fully (counterclockwise). Use a soapy 

water solution to check all connections for leaks before 

attempting to light the grill.    See below. If a leak is found, 

turn the tank valve off and do not use the grill until a local 

LP gas dealer can make repairs. 

 

To disconnect LP gas cylinder: 

1.  Turn the burner valves off. 

2.  Turn the tank valve off fully (turn clockwise to stop). 

Detach the regulator assembly from the tank valve by turning 

the quick coupling nut counterclockwise 

 

K15Y06P-1